We use this to back up 200GB every night to an exabyte 210. It has clients for most everything, server is similar. We run it on Linux. Don't remember a Mac client, however, use netatalk, and have the Mac copy itself to a volume on the Linux Box...then back up that volume.
When applicants here want to ensure thier resume gets seen by someone who knows something, they do 1 of two things.
1. Call the organization and ask for the IS Dept. Once speaking to the IS Dept, explain that you have just submitted a resume for job XXX and that you aren't sure it has all the keywords and tricky phrases, but that you are more than qualified. Please leave a note for the IS Director/Dept Manager/etc to the effect that Person: So-and-So has applied.
Our Managers then ask HR where the resume from XXX is. Very effective....after the first few of these, HR stopped any attempt at weeding out resumes.
2. They call the org and ask for the IS Helpdesk..then follow approximately the same procedure as above.
Wire mesh is just fine for basic emf and rf shielding... It should be roughly contiguous, although, that is hardly worth pulling out a micrometer of magnifying glass.
Just make sure each seperate piece of mesh when assembled makes good electrical contact with the frame? (if you have some sort of framework on this) or other conductive bus. To test if this is roughly adequate, 1. get a multimeter (measures voltage/resistance and usually current, sometimes mislabeled a voltmeter) 2. set it to measure resistance or continuity. 3. touch 1 probe to one portion of mesh, the second to a point opposite...as in as far as you can get inside the case from point 1 4. look at the resistance readout. 5. It should read 0 ohms (if yours has a floating needle, it may be a bit off, not to worry) If it reads anything > 1 ohm, you don't have a significantly conductive material to be useful as a shield/ground... (For those who will argue here...I just finished measuring the foil from a pack of marlboro light 100's that came out to 200 mOhms , or 0.2 Ohms, in case you cared.)
Now for the final key point. Ensure that the power supply is properly grounded, your shield is properly grounded, and that your new case is plugged into an adequately grounded 3 prong receptacle.
For clarification...if you don't plug it into a grounded receptacle, what you've just configured is essentially a floating common attached nicely to a power cord which sould make a passable antenna for rebroadcasting all the stuff you just collected.
If you need to add a better ground to your house...i.e. you get lines in the tv when you run the vacuum...talk to an electrician unless you are comfortable in a circuit breaker box. You can get a 3-4 foot copper clad steel rod, with copper wire, to act as a grounding rod. have the electrician hook up the copper wire to the ground bar in your circuit breaker box, then you attach it with a clamp to the grounding rod.
Note..you're going to need a sledge hammer...preferably a big one... Apply the sledge hammer to thetop of the grounding rod until only about 3-4 inches sticks out of the ground.... now attach that wire, and your house ground should be much better.
Whew...wrote a lot more than I planned...but you get the idea.
Slashdot Mirror
We use this to back up 200GB every night to an exabyte 210.
It has clients for most everything, server is similar.
We run it on Linux.
Don't remember a Mac client, however, use netatalk, and have the Mac copy itself to a volume on the Linux Box...then back up that volume.
When applicants here want to ensure thier resume gets seen by someone who knows something, they do 1 of two things.
1. Call the organization and ask for the IS Dept.
Once speaking to the IS Dept, explain that you have just submitted a resume for job XXX and that you aren't sure it has all the keywords and tricky phrases, but that you are more than qualified. Please leave a note for the IS Director/Dept Manager/etc to the effect that Person: So-and-So has applied.
Our Managers then ask HR where the resume from XXX is. Very effective....after the first few of these, HR stopped any attempt at weeding out resumes.
2. They call the org and ask for the IS Helpdesk..then follow approximately the same procedure as above.
Wire mesh is just fine for basic emf and rf shielding...
It should be roughly contiguous, although, that is hardly worth pulling out a micrometer of magnifying glass.
Just make sure each seperate piece of mesh when assembled makes good electrical contact with the frame? (if you have some sort of framework on this) or other conductive bus. To test if this is roughly adequate,
1. get a multimeter (measures voltage/resistance and usually current, sometimes mislabeled a voltmeter)
2. set it to measure resistance or continuity.
3. touch 1 probe to one portion of mesh, the second to a point opposite...as in as far as you can get inside the case from point 1
4. look at the resistance readout.
5. It should read 0 ohms (if yours has a floating needle, it may be a bit off, not to worry) If it reads anything > 1 ohm, you don't have a significantly conductive material to be useful as a shield/ground...
(For those who will argue here...I just finished measuring the foil from a pack of marlboro light 100's that came out to 200 mOhms , or 0.2 Ohms, in case you cared.)
Now for the final key point. Ensure that the power supply is properly grounded, your shield is properly grounded, and that your new case is plugged into an adequately grounded 3 prong receptacle.
For clarification...if you don't plug it into a grounded receptacle, what you've just configured is essentially a floating common attached nicely to a power cord which sould make a passable antenna for rebroadcasting all the stuff you just collected.
If you need to add a better ground to your house...i.e. you get lines in the tv when you run the vacuum...talk to an electrician unless you are comfortable in a circuit breaker box.
You can get a 3-4 foot copper clad steel rod, with copper wire, to act as a grounding rod. have the electrician hook up the copper wire to the ground bar in your circuit breaker box, then you attach it with a clamp to the grounding rod.
Note..you're going to need a sledge hammer...preferably a big one...
Apply the sledge hammer to thetop of the grounding rod until only about 3-4 inches sticks out of the ground....
now attach that wire, and your house ground should be much better.
Whew...wrote a lot more than I planned...but you get the idea.