Slashdot Mirror
Home Server Rooms?
Tuzanor
writes "I've got a buddy moving into a brand new house. Being
geeks, we've decided to wire the house with a large home network.
While this story
took care of wiring the house, we need to figure out how to create a
well set up server room. We'll be having both towers and rack mounted
computers as well as various switches, UPSes, etc. Also, we figure
this room will get warm, even in winter. How may we cool it while
still keeping the rest of the house toasty warm on a cold
Canadian night (without opening a window)"
Check out geothermal cooling. Dig about 5 - 7 feet down into the ground and you've got a consistent temperature *year 'round*. The temperature happens to be ideal for cooling in the summer and heating in the winter.
It'd be *ultra geek* if you could set up a processor cooler based on this technology.
Life is the leading cause of death in America.
A good home server room is just as good as the design behind it. That's probably why it's an AskSlashdot question. An apt one, too.
In my home, I set up my server room before we even officially moved in. I can get pics if people desire, but I'll give the gist here.
First, it needs to be in the basement. Some people think it's only a heat issue, but the reality is that server rooms are noisy. I've only got four machines whirring about, and that alone is enough to sound like a wind tunnel.
Second, build shelving such that you can walk around it and access equipment from the rear. How many tower cases have RJ-45 connectors on the front side? Didn't think so. I built shelving out of 2x4's, 3/4" plywood, lag bolts, and drywall screws. Some day I'll get around to putting formica all over everything (it's not that expensive and easy to do). Everything is strong enough to hold me jumping up and down without any wiggle.
Third, carefully design how your wires are going to run. Raceways are a great idea, though you can also go the cheap route and use ziptie loops that have screw holes. Also, network wires should not be in the same raceway (and not parallel) to power cables.
Finally, place your equipment. Servers should be placed where they most make sense, e.g. don't put the internal file server next to the router and the public webserver on the other end. People should get a "feeling" of what your machine's duties are visually. Also, keep networking gear all in the same area--hubs, switches, and even modems and your incoming ISP equipment. That's also the best place for your router.
In addition, consider a KVM. They really are helpful, and cut down a lot on heat (and space needs). Some even have remote extenders--with mine I can work on any machine in my server room from my desktop in my office area. Definitely beats working in the wind tunnel.
Long, cute, or funny Sigs are just another form of over compensation, used by geeks, nerdz, etc.
I am dead serious when I tell you know I know two people who run a very successful consulting firm around my ara who have their servers in a bathroom inside their house. When I asked them why they put them there, the answer was "We don't use this bathroom, it's in the middle of the house, and it's the most secure since it has no windows in it."
:)
Ask serious questions, get slightly stupid answers
The exhaust fan sounds better to me -- most equipment is designed to be air-cooled in a cool-room-temp environment, so dragging the house-air through the room makes sense.
If you want to get really wild -- insulate the interior walls and cut a window, then mount a window air conditioner across the interior wall to pump heat from the server room into the house proper, recycling instead of dumping.
Ummm, you don't bury the computers, you bury about a mile of poly tubing, and circulate a water / glycol mix. Hook that up to an old AC core (or a new one, it's your money...) and you
have yourself a basic heat transfer system. Add a compressor and you have a heat pump. Big project, and expensive (cost of digging deep enough and tubing). If you heat / cool you whole house this way, it may pay for itself.
What I did for my room, was add a few electic dampers, duct blowers, thermostats, and a few relays and you have yourself a REALLY simple climate conrtol system.
You have 4 ducts: exhaust to outside, fresh outside air (filtered), furnace (a/c), and furnace return. Use thermostats to control which ducts are active based on temps inside, outside, etc.
When it's cold outside, you have free AC. When it's warm, you tap off the main house AC. Dual zone control on furnaces are common. I don't care how cold it gets in the room, so heating isn't required (it doesn't get below 30 outside here, and the server room. You can't actually recycle the waste heat as the room is ALWAYS cooler than I normally keep the rest of the house.
I actually have a new modern furnace and A/C that can run at 3 different levels which works awesome for this project. I also have an electronic air cleaner, and run the blower 24/7/365 filtering the house air (allergies...)
It shouldn't be too difficult for you to set up some thermostatic switches to control the system. Just make it blow cold air (even from outside) into the server room when it's needed and blow the hot air into the rest of the furnace system when you need that in the rest of the house.
If the server room is going to be in the basement, you probably could just put a blower vent going into the main flume from near the ceiling of the server room, and then spill the cold air from the rest of the house (or just some of it) into the server room, again from the ceiling. Then it'll be the coolest room in the house, and not just because it has a bunch of computers!
Here's another tip, put the hot-air sucker near the outside wall, and the cold air blower nearer to the center of the house. That'll keep the air moving and thermoclining (layers of different temp air).
Good luck!
My Karma was at 49, then they switched to words. All that work for nothing!