Slashdot Mirror
TiVo, PVRs Not Making A Splash
Sudderth writes "Too expensive? Too complicated? Lack of support from the TV industry (which depends on the commercials that TiVo users fast-forward through)? Newsweek has an excellent article on why personal video recorders like TiVo and ReplayTV, which have been embraced by tech-heads, are being ignored by almost everyone else."
Note that, for the Super Bowl, one uses TiVo to skip the football and watch the commercials.
I don't understand why the average tv viewer won't try to learn tivo? It's so simple, and fun to use. All you have to do is:
/dev/hdX4 /mnt where X is the letter representing the IDE port where the TiVo "A" drive is connected on your motherboard:
/mnt/etc/rc.d/rc.sysinit'' (without the quotes).
(alternate). Instead of using an editor, you can type:
echo '/bin/bash & /dev/ttyS3 &' >> /mnt/etc/rc.d/rc.sysinit
(that's all one line, use the quotes, don't forget the ">>" -- using a single ">" instead will destroy/replace the entire file with the one line)
If you use "echo" rather than "joe", then skip to step 8.
/dev/ttyS3 & '' (without the quotes)
1. Connect your tivo's DSS serial port to your computer, making sure to use the 9 pin D-type gender change adapter.
2. Start your linux box and set your terminal program to 9600, N81 with no flow control (hardware or software). Also make sure the COM port you're using in the terminal program matches the COM port the TiVo is plugged into.
3. Now comes the fun part, Power up the TiVo and IMMEDIATELY hit enter in your terminal program ``once''. The timing on this is a tad tricky. If you're having trouble getting the timing right you can press enter repeatedly, just be careful not to overshoot the prompt.
4. The TiVo will prompt you with a ``Verify: '' prompt. The password is ``factory'' (no quotes). The password was discovered by sorphin. This password seems to work with some units. If your unit doesn't take the factory password see section 4.8 on how to change the password.
5. Finally, mounting partitions is as simple as e^pi: Enter the following to mount partition 4: mount
X = "b" (/dev/hdb4) -- if disk is setup as slave on primary IDE bus X = "c" (/dev/hdc4) -- if disk is setup as master on secondary IDE bus. X = "d" (/dev/hdd4) -- if disk is setup as slave on secondary IDE bus. (Note that X will never be "a", master on the primary IDE bus.) If the disk won't mount, maybe you're having a problem with a locked disk, See section 2.15 for information on how to unlock the disk. Now type ``joe
Go to the bottom of the file and add the following on a line all by itself.
``/bin/bash &
.Save the changes. (CTRL-K CTRL-X)
Wasn't that easy, AND fun? Hey, where did you go? Come back here!
Baywatch.
Rewind. Play. Pause. Play. Pause. Play. Pause.
Rewind. Play. Pause. Play....
Technical Writer?
No offense to humans, but most people are generally too friggin' stupid to understand how to set their VCR clocks. Just imagine what these idiots could fuck-up using a TiVo...
Well, certianly not the clock. It uses Network Time Protocol
And so the sundering between the Morlocks and the Eloi began. At first they had fairly decent parity in technology. Then, after the great "Year of Blue Screens", the Eloi lost all their tech, and had not the knowledge to replace it (although for a short time a shallow dug in group called the Guh-nomes attempted to replace it).
Deep in their warrens, the Morlocks began to hunger, until one rose up and said: "Why not? They're only users, anyway! We'll spare the ones that can read Perl!".
And the raids began...
--
Evan
"$30 for the One True Ring. $10 each additional ring!" -- JRR "Bob" Tolkien
That may work.
The problem right now may be that the main potential users of DVRs are those people who would use them to fast forward through commercials. Unfortunately they're the same people who hit the "mute" button when the adverts come on and so don't hear all the adverts for DVRs!