Slashdot Mirror
Monitoring the Health of Your Penguin?
codepunk asks; "I work for a large manufacturing firm in the midwest, working on a migration from Windows to Linux in the data center. We just completed installation of two full Oracle RAC 9i clusters. We are also in the process of configuring two clusters for our manufacturing floor's Linux desktop roll out. The machines that make up our data center are all Compaq Proliant Series machines. In order to facilitate hardware maintenance we are in bad need of a monitoring solution. HP offers Insight Manager as well as the Compaq Health Agents. This solution
would seem like a natural but the drivers installed by these solutions are binary only. We have never managed to get these to work correctly and are really concerned about the stability of our systems with these modules loaded. We are not opposed to buying hardware in the future from a vendor that provides a more open solution. We are also not opposed to buying a open third party solution. Slashdot, what do you use for Linux system hardware monitoring?"
I use Loggerithim.
Big Brother is often a good choice.
____
nico
Nico-Live
I think you can probably get the same end result with the projects mentioned above, but you might check out Nagios. It has a nice web interface and provides a wide array of monitoring options.
Just to clarify for other readers, he's asking about the Compaq health and wellness drivers which are binary only kernel modules and daemons that monitor things like the power supplies, temperature, if the case was opened, the speed and health of every fan in the system as well as things like memory errors and the state of the hard drives. They provide information that things like Nagios and Big Brother won't be aware of because the information isn't in /proc without these drivers.
That being said, you'd do well to subscribe to the Compaq and Linux mailing list. There are some solutions to getting those Compaq drivers working with versions of Red Hat that are newer than what Compaq supports. I haven't had the time to try any of the suggestions out on one of our servers yet.
Also, since everyone else is thinking you want application monitoring, I'd recommend Nagios.
Prevent email address forgery. Publish SPF records for y
There are a variety of agents and monitoring tools that make up the Insight Management toolset. We've found that some of the tools are better than others.
Pretty much the only *essential* tool that's required is the cpqhealth drivers and daemons. This poll the health of the onboard systems such as fans, CPUs, disk arrays, etc, and will log to syslog when there is a fault. Unforunately, the open source lm_sensors and cpqarrayd packages don't talk to the hardware in the new G3 DL380's, so cpqhealth is your only option. You can find it on HP's support site, as part of the hpasm package for Linux... I grabbed my copy for RedHat 7.3 from here.
cpqhealth comes with pre-built modules for RedHat 7.3, 8.0 and a few other distros (SuSE for example). But I've found that even the most up to date stuff from HP's site only supports the kernels shipped on the RedHat cd, and nothing newer. Luckily, cpqhealth (part of the hpasm package) does allow you to build new modules. You'll need a compiler on the machine. Take a peek at this script: /opt/compaq/cpqhealth/custom_cpqhealth.sh - it will build a new cpqhealth RPM for you, containing the drivers and daemons necessary to log hardware faults to the syslog (as well as to take action on them).
The script will break when you first run it - it will look for the following two files:
Both of which are missing in the most recent hpasm release. Create the S10cpqasm file yourself (it's just a startup script that gets dumped /etc/init.d - a simple touch of that file is fine for now - you can put a proper one together later), and copy hpuid from /bin (where it gets installed when you installed the hpasm RPM).
Once done, you'll have an RPM that installs the following:
two kernel modules: cpqasm.o, cpqevt.o
two daemons: /opt/compaq/cpqhealth/cpqasm/casmd
/opt/compaq/cpqhealth/cpqevt/cevtd
Make sure the kernel modules and daemons get loaded, and you'll now get warnings when a fan fails, disk in the RAID array dies, etc.
Even better - unlike the rest of the HP/Compaq Insight stuff, this doesn't use SNMP, doesn't install a web server that listens to 0.0.0.0, and seems to work quite well.
Other annoying things I've discovered about the rest of the HP/Compaq toolset:
In the end, we just ended up installing cpqhealth on the boxes to warn us of hardware problems, and will use RRDtool for our other monitoring requirements.
BMC have a good few Linux server mananagement stuff. BMC Patrol is one of them.
And so do Candle: Omegamon XE for Linux
We started using Director on xSeries hardware, and it seems to work alot better than insight manager.
The SNMP traps (or Tivoli TEC events in our case) are alot more intuitive and useful than the crap that insight manager sent out, and the agent seems to be more reliable. You can use a "Director Server" or a product like Nagios or OpenView for alerting.
Keep in mind that "Systems Management" in the pc/unix world is a black hole that consumes time & money. You might be better off using something like VMware GSX server on big Intel hardware or even an IBM zseries and use virtual hosts.
One of the advantages of big, expensive hardware is that they often come with service processors that phone home or page you when problems occur. At our shop, several admins have been suprised when an IBM repairman calls to schedule replacement of a failed disk or fan that they were unaware of -- the service call was generated automatically.
Conformity is the jailer of freedom and enemy of growth. -JFK
You face a similar problem to pretty much any hardware specific driver issue when it comes to Linux: the O/S tends to be ignored by the vendor.
Open-source tools tend to be (gasp) based on open protocols, whereas hardware tends to have its own specific, closed methods for determining state (such as temperature, etc.). The only real way to solve the problem is to reverse engineer the available methods or patronize those vendors that offer either an open solution or wider selection of supported O/S's. I believe that Compaq embeds some code from BMC Software for monitoring low level hardware information, so it is doubtful you will ever see the source for it.
Off the top of my head, only Dell's OpenManage is available for Linux.
If you can find a way to access the information from the command line, you can always use net-snmp to integrate it into an SNMP agent that can be accessed by most management products.
Good luck, and if you get it working you may want to check out OpenNMS as your monitoring solution. It supports CIM out of the box (as well as Dell OpenManage).
I use a combo of big brother, SNIPS, MRTG and NUT(Network UPS tools). I have a demonstration page here:
:)
.aphroland.org e.g. snips.aphroland.org bb.aphroland.org etc..
http://monitor.aphroland.org/
(best viewed in 1600x1200 or higher)
instant network/system status from my home network. plenty of performance monitoring stuff, availability tracking etc. Works wonderfully. Took forever to setup though, most of that was determining what to monitor and how to monitor it, these days I can set it up in a few hours.
I also use PureSecure(www.demarc.com) for NIDS and HIDS. That data isn't available at the above url though some of my snort activity is.
please don't slashdot it as it puts a somewhat
heavy load on my system
I hacked up a couple of the tools(SNIPS/NUT) to display much more compact information so it would all fit in 1 page. with the exception of nut, all of the 3 other tools are individually accessable from
Surprised that no one has mentioned Nagios. Used to be called Netsaint. We've used it to monitor about 10 servers for about 3 years now. It's good for monitoring almost anything about your hardware you can think of, as long as you have the ability to get back the extended information from your motherboard (temperature, etc). It's open source, with many plugins & writing plugins for it is very simple.
InterMapper can monitor anything that responds to SNMP or other TCP/IP queries. For the central monitoring server, it is available now for Mac and Windows, and in beta for Linux.
You asked slashdot, but didn't ask freshmeat?! OSDN is your one-stop shop for all you computing needs! OSDN is great! OSDN is good!
:: System :: Networking :: Monitoring :: Hardware Watchdog (90 projects)
# Topic
Bow down before OSDN! Huzzah!
I know everyone hates Caldera/SCO around here, but Volution is solid, feature-rich, and made by a Linux company still actually in business. Monty
Zabbix is Open Source software that will probably perfectly fit into your environment. Zabbix has its native high-performance agents virtually for every OS. All collected information and configuration data is stored in the RDBMS. This is big advantage! Zabbix also allows to look at everything you monitor from business point of view (SLA, service availability, etc). It has maps, alerts, triggers, user-based permissions and more. Check screenshots to get overview of functions it offers.
You might want to take a look at the Darksite remote management card from Crystal Computing. I don't work for them, but I had the chance to try one out, and I liked what I saw.
Basically, it's a single-board computer that sits in a PCI slot in your server, and monitors its vitals (hardware / software). It runs completely independently of your server, except for an optional OS agent that can monitor things like memory utilization, CPU activity, etc. (Yes, there is an agent available for Linux).
It has a web-based administration interface, and can send you alerts and warnings via Email or pager, even if the main server locks up hard for some reason--in that case, you can perform a remote reset or even cycle the power, all from a web based interface.
It's a pretty nifty card--you should take a look.