The Best VHS Capture System Using Free Software?

mrcgran asks: "I have been trying to find the best solution to transfer VHS tapes to a digital format using Free Software only. I would like to lose as little as possible in the conversion, sampling optimally, minimizing noise and being in control of every step of the process. Storage is not a problem. I'm expecting to use around 5GB+ for each hour of raw captured footage." If you were going to build a VHS capture system using Free Software, how would you do it?

The software part seems promising: VLC and mencoder for conversion of raw footage, Cinelerra and many others for video editing.

However, the hardware is being tricky. Most try to bloat the device adding functions like TV/compression/edition instead of focusing on the raw A/D conversion. Chipsets are hidden, and parameters like signal-to-noise, sampling rate etc are unavailable for comparison. Information is scattered and very difficult to find.

Which chipsets/products should I look for, specially for use with Linux and BSD? Which ones allow oversampling of pixel resolution and number of frames (in order to average the values and reduce the noise)? Which setup should I use: S-Video/Composite, sampling rate/oversampling, suggestions on high-quality VHS players/heads/tape cleaning processes, etc? Has anyone tried to use scaling algorithms such as hq/scalenx to upscale video and sound resolution? Pitfalls?"

Comments

The sky's the limit

[moosesocks]

You're right that you're going to run into hardware problems unless you choose very carefully.

As is the case with most things related to analogue/digital conversion (and also to video editing), the sky's pretty much the limit when it comes to the amount of money you can sink into your equipment.

For starters, a broadcast-quality VCR will set you back quite a bit. Great capture hardware's going to do you no good if the quality of the source is poor. We'll leave this part as an exercise for the reader.

Now that you've got a decent VCR, you can go splurge on an expensive Analogue-Digital converter. Any decent-quality device won't offer all of the unnecessary "bells and whistles" (such as hardware-based MPEG/WMV encoding) that the parent poster describes. Instead, most pro-grade boxes will take an analogue signal (RCA, S-Vid, or even BNC if you want to go all out), and output a standard FireWire DV signal that any decent video editing software should be able to handle. Canopus' hardware is very well-regarded for these purposes. Their products range from somewhat inexpensive (~$150) for consumer-grade products to appallingly expensive for the pro-grade stuff.

However, the fact that you were considering using a TV-tuner card to do the capture seems to indicate that you haven't done anything like this at all. If your content is bad enough that you really NEED to be "in control of every step of the process", you're better off outsourcing this to a professional. Otherwise, a decent VCR and A/D converter should clean up the signal pretty well for you. You can always take care of things like de-interlacing in software later on.

I might also recommend stepping down from your podium, and considering editing your video with non-free software. I can't help but think that the gap that exists between Cineleera and Final Cut Pro is even bigger than the gap between Photoshop and The Gimp (which is pretty huge). Most professional studios use either Avid or Final Cut (and I'm really not trying to be an apple fanboy here -- Apple and Avid basically jointly own the entire industry). Compared to the rest of the costs of video production, Final Cut is a steal.

Alternatively, there are VHS/DVD-R decks out there that will automatically make dubs for you. Sony makes one, and it costs around $200 the last time I checked. Quality's not going to be the absolute best, but will still be pretty darn good. And it's easy as long as your source doesn't have macrovision.

Using a DVD recorder

[Rastignac]

Plug the VHS reader with the DVD recorder. Play the tape and record it on a DVDRW (using highest available quality). Voilà. That's the easiest way to do it, and the quality is good. Now put the DVDRW in your PC, and get the files (MPEG2 VOB), and use any software for editing them.