Slashdot Mirror
How Best To Deal With WiFi Interference?
marciot writes "I live in a condominium where I get interference from my neighbors' WiFi. I understand that 1, 6 and 11 are the only non-overlapping WiFi channels, but how does this translate into real-life best practices? When you must overlap, is there a 'good' way to do it? With nine access points, for example, is it better to have three APs each on 1, 6 and 11, so that each completely overlaps with only two others? Or is it best to distribute those APs across nine channels such that they only partially overlap others (but potentially overlap more APs in total)? Do use patterns affect interference? For example, is it best to overlap a channel with multiple APs that rarely transfers data, or to share a channel with one person who downloads torrents 24/7? Does maximum data rate affect interference or robustness to interference? I found out by accident that setting my access point to '802.11b only' mode appeared to give me a vastly more reliable connection that leaving it in 'mixed 802.11b/g.' Is this a fluke? Or does transmitting at 10 Mbps when everyone else is using 54 Mbps (for their 3 Mbps DSL pipes!) give you a true advantage?"
The 5GHz band has been basically forgotten by the mainstream. This is your chance. Equipment supporting 802.11a is a little bit more expensive and 5GHz doesn't work so well through walls, but other than that it's pure upsides.
Finally! A year of moderation! Ready for 2019?
You can minimize interference, but don't expect too much.
First, I don't know what type of antenna's you use, but escaping from vertical polarization (which is 'default'), to horizontal one.
Difference in signal level between these two are 20 dbm. So, if you'r getting signal level from your neibh. -70, you will be getting -90, which will greatly improve your wifi stability.
Next, use channels that have lesser bandwidth consumption. It's not important how many ap's are on one channel, it's important how many data frames are going in and out on that channel.
I tested few days ago, my wifi nodes are receiving data from 3 channel bellow/above me, so cuz I use 11, that means I get data from channel 8, but not from 7 that much. Some packets get through, but that's nothing. Which means, if there's traffic on channel 6, you can safely use channel 9, and you won't feel interference blocking you.
Changing data rate, means changing signal modulation. If you use G or A(if you can, use 802.11a), OFDM modulation kicks in, which from my experience deals better with noise. Latency is far more better then on any modulation of B.
So, try putting your devices on G, then fix the rate to 11mbps.
Basically ... there's no real escape from noise. I'm dealing with it for years now, and I'm getting sick of it ... even polarisation changes aren't effective anymore. That's why, I recommend to switch to 802.11a, there's more then 30 non overlaping channels.. or go above/bellow frequency range. Like .. channel 15 on 2.4. It's possible to do.
Do you and your neaghbors all need your own seperate LAN's ?
If all you are doing is a bit of surfing, it might be worth knocking on doors and offering to set up an open access point. Of course, some will need a private LAN of there own, but most will probably jump at the chance to split the ISP bill with you and reduce the interferance.
Remember, they will be suffering with crap wireless just as much as you are. If you are a geek, you will be the one in the best position to help everyone out.... and meet your neigbours for a beer in the process
Anyone quoted by a reporter knows how little they understand
Don't believe what you read is the truth.
Use NetStumbler http://www.netstumbler.com/ to determine the signal strength of all the other access points to see if any of the channels will have low interference. Although you may see lots of access points, they could be very feint signals because beacon frames are short at about 50 bytes (compared to 1500 for a typical data frame) so they're a lot easier to receive. The strong signal from your own apartment/condo should be able to drown out the noise from all the feint AP signals but if the people next door to you have an AP then it could slow you down so that's why you need to check for strong signals with NetStumbler.
Changing your beacon interval to 101 keeps your wifi networks beacons perpetually out of sync with your neighbors wifi noise. The problem every one is having is errors like unable to find access point, connection error, and being dropped from your access point. This single change makes all of the other tweaks esoteric and uneccessary. Access points know how to deal with noise and interference. Access points do not know how to deal with an excessive amount of lost beacons. And they shouldn't.
http://freegnu.blogspot.com
http://identi.ca/freegnu
Most plebes don't know how to tweak their north american firmware/drivers for channel 14, but us 133t /. d00ds do. The hardware all supports it (tell it you're in Japan), and 14 is far enough from 11 that you're only getting a bit of overlap, and only on one side.
Just don't tell the FCC.
Do daemons dream of electric sleep()?