Slashdot Mirror
Raspberry Pi A+ Details Leaked
mikejuk writes Despite trying to keep it secret, a major Raspberry Pi retailer has published some details of the upcoming model A+ Raspberry Pi thanks to a product page that went live early. The board layout looks different and is much smaller than the model A or B+. Judging from the photograph, the A+ board encompasses the four standard mounting holes, which makes it approximately 56x65mm — the model B+ is 56x85mm.
The key improvement is the new 40-pin GPIO socket, which makes the model A+ fully compatible with the HAT expansion standard. This means that any new HAT expansion cards should now work with the A+. It also has what's likely a connector for the yet-unreleased Raspberry Pi touchscreen. Another welcome change is the micro SD slot. One downside of the A+ is that it still has only a single USB 2 connector.
The key improvement is the new 40-pin GPIO socket, which makes the model A+ fully compatible with the HAT expansion standard. This means that any new HAT expansion cards should now work with the A+. It also has what's likely a connector for the yet-unreleased Raspberry Pi touchscreen. Another welcome change is the micro SD slot. One downside of the A+ is that it still has only a single USB 2 connector.
I know, the Raspberry Pis are not truly powerful, but because of their low price and easy expandability, they are useful for so many creative projects.
For my own use, I was thinking of turning mine into an airplay-compatible receiver (I found that there is software for for that) and built it together with (wifi dongle and a little amp) into a very old radio cabinet. Nice to put in the kitchen.
The popularity of the arduino shows that CPU performance is not everything. rpi is fast enough to do many tasks, it is small, cheap, widely available, well documented and well supported. That's why its popular.
One downside of the A+ is that it still has only a single USB 2 connector.
There are two down sides worth noting. That's one of them; have they got USB figured out yet? Just one port is bad enough but if they bugger the polyfuses again... But the real problem is the RAM. 512MB is cramped. 256MB is unacceptable.
"You're right," Fisheye says. "I should have set it on 'whip' or 'chop.'"
The processor in the existing rpi is so slow compared to other (even similarly clocked) modern arm cores that one might seriously wonder if Intel isn't paying these folks to sabotage arm in the minds of developers.
Raspberry Pi is not a product that follows the latest computing advancements but it is about keeping a stable platform. A program written for C64 works on another C64. A program written for Raspberry Pi works on another Raspberry Pi.
It would make cooperative education and hobby projects more difficult if people had to continuously negotiate about "is this the 700MHz or 1000MHz version we are talking about". It's more straightforward to have a common ground.
Of course there's plenty of other ARM boards with the latest hot chips if that's what your project requires. :)
It's also about being cheap. The Pi was expressly designed for use as an educational platform for use in schools. Children break everything, so the pi needs to be cheap enough that a school can keep replacing all the ones that get snapped/squished/thrown/scratched/smashed.
Well supported? What? Seriously, what are you talking about? A bunch of random idiots on some forum that don't know jack shit about the hardware or the software does not make it well supported.
Just stop trying to pretend the Pi is awesome. It was an awesome idea before it came out, everything since then has been horrible. Production delays, lack of supply (Seriously, how the fuck can you not meet demand for years on end), bad hardware design, closed source GPU blobs that only work on specific linux distros and NOTHING ELSE.
Its crap. Wake up and smell the shit on your nose.
So cus' the thing doesn't do exactly what you want, it's bad?
It's not the holy grail of anything, but it's available and it does its just just fine.
Admit nothing. Deny Everything. Make Counter-accusations.
There's a lot of overlap between those constraints. Cheap doesn't just mean cheap to buy, it means cheap to replace. And that means that when you break one, if the exact model doesn't exist anymore then you need to be able to run everything that was working on the old one on a newer model. The advantage of the RPi over more powerful ARM boards is that it comes with that guarantee - the A+ will run everything (including the same OS image) as the A and B.
The hypothetical 700MHz vs 1GHz issue that the grandparent talks about isn't that much of a problem. More importantly, a new SoC would likely be dual (or quad or octo) core and would be ARMv7, not ARMv6. That's a big change. I expect that the RPi will skip ARMv7 entirely and that eventually there will be an ARMv8 model (possible ARMv8.1 / ARMv8.2), but the jump to 64-bit gives a good excuse for needing a new OS image.
Disclaimer: I work a couple of floors below several of the RPi Foundation, but the only thing that they've told me about their future plans is that they have some. Everything in this post is uninformed guesswork.
I am TheRaven on Soylent News
Many tasks,
http://hackaday.com/tag/raspbe...
http://makezine.com/category/e...
Seems to me like thousands of people are finding interesting things to do. Of course it is not fast enough for everything, but nor is my i7 laptop, or the 48core server box I use at work.
Small. Ok, that's relative. Its been fine for my uses, smaller than the beagleboard and mini-itx boards I used before. The A+ is even smaller. Interested to know what project you are doing where the pi is too big and too slow, what do you use instead?
Cheap. sorry if $25/$35 is too expensive. Its a quarter the price of the beaglebaord that I used before. Maybe you can find something cheaper for your specific task.
Widely available. In the UK there are several high street shops with it in stock, and lots of online retailers.
Documentation. Personally GPU docs don't interest me (though they are now released, so its the most open arm SoC). When I have wanted to use the pi in a project I have found lots of documentation and tutorials to help me.
Well supported. 2.5 years after release they are still doing regular software updates, including big things like wayland support. Compared to lots of hardware that is released with some old distro image that never gets any updates.
So yes the raspberrypi is awesome. It lets lots of people do interesting things at a good price. Sure for certain things an atmega, beaglebaord, banana pi, gumstix, galileo, an old pc or something else might be better.
It is garbage because a very closed CPU is used as an educational platform without datasheet availability.
This Broadcom SOC is great for mass-produced routers, bad for sharing with people trying to learn how Linux boots, learning assembly and possibly advancing to their own RTOS. I'm aware of the measly peripheral datasheet sections that are available online, but for Atmel and NXP chips one has to read a LOT more to make basic hardware level programs (how are the VICs nested, timing and boot issues/settings, other exceptions made by Broadcom i their ARM11 implementation etc).
Consistency is unimportant if youre giving people a board with the OS pre-installed, the kernel can handle different CPUs while users use different programs. But if you want to learn a bit more and go lower level (for example from Arduino), you're screwed by Broadcom SOC's severe lack of documentation. And forget about learning to code for the GPU.
"Give orange me give eat orange me eat orange give me eat orange give me you." -Nim Chimpsky