Slashdot Mirror
Homemade Silly Putty
kinema writes "Have you ever wanted a ball of Silly Putty as big as your head? Now you can make it at home. The University of Minnesota's Chemistry Department has instructions on how to make it on their website." Isn't silly putty a copyright circumvention tool? This should be regulated before it gets out of hand.
It IS copyrighted.. so that page COULD be shut down by ( i think ) hasbro..
Gotta love the society we live in now..
---- Booth was a patriot ----
Another slime recipe can be found here as well.
The instructions by themselves are not particularly instructive: "the procedure can be followed from the slime procedure above."
This is mentioned here. There's a bunch of other cool stuff in the same section, too.
It's amazing how a chemical compound created while trying to devise better ways to kill enemies works out to have recreational purposes.
And they say America spends too much on military research.
Any terrorist handbook worth its salt has had recipes for putties for years. OH! SILLY putty! I was thinking EXPLOSIVE putty! My bad.
This actually looks a lot like the recipe for Gak. The only difference is that Gak uses Borax, which, for all I know could be the same as sodium borate. Are Gak and silly putty perhaps the same except for the glue to sodium borate ratio?
Have you ever wanted a ball of Silly Putty as big as your head?
I'm hydrocephalic, you insensitive clod! I'd prefer a smaller head, thank you.
"Now you can make it at home"
Okay, sure, I'll just pull the sodium borate out of my cabinet under the sink.
Back in my freshman year Chemistry Lab 4 years ago one of the experiments was to make silly putty. I remember it was one of the simplier labs to do, but the end result didn't come out very good. It dries out very quickly, and isn't as "flexible" as the stuff you buy in a store. It broke very easily. I don't remember if the teacher gave an explaination of why the putty we made wasn't as good as the store bought stuff, but I do remember getting the impression that you weren't going to get anything high quality in a small one off run.
My cousin gave me a recipe for making this from domestic materials... Salt has lots of sodium, and most brands of the toilet cleaner contain borate. Let me see... if I just mix a little of that with some garden fertiliser, then shake the whol >BOOOM
Ceci n'est pas une signature
This recipe is a clear violation of the DMCA, in that the end device is capable of copying copyrighted materials (newspapers) and defeating their protection mechanisms (if they've been printed backwards).
Bah weep granah, weep ninny bong!
For those of you who are lazy here are a couple of links to buy silly putty in bulk.
From Crayola
Or if you would like to buy 100 pounds of the stuff you can apparently order it directly from Dow Corning. Here's a page with step by step instructions on what to ask for and who to call.
100 Pounds or More
sodium borate is borax. seems rather odd to have a recipe that includes elmer's glue combining with an esoteric chemical when there's a much commoner name that could be used...
Glue borax and water.
Its not really the same consistancy of silly putty from the times Ive made it.
Check out this link for these recipes.
... is whot bwings os tugevza tsuzay.
from www.sillyputty.com
"Silly Putty is a dilatant compound, a silicone based polymer..." This statement makes sense also because the inventor was (is) a Dow chemist/engineer. Dow has always been a leader in silicone chemistry.
The recipie from U of M is a borate cross-linked PVA (from the Elmer's), better known as slime. This is NOT a silicone polymer.
Before I flame UofM Chemistry dept., I will give them a change to correct this gaff.
sigs are for losers (except to point out that sigs are for losers)
Have you ever wanted a ball of Silly Putty as big as your head?
Why, yes! Yes I have!
Now you can make it at home.
"We went to the bars and then a house party last night. What'd you do?"
"I stayed at home and made Silly Putty! I'm going to kill myself!"
The coolest voice ever.
Dow 3179 Dilatent Compound is. It is silicone-based, like the Horta.
You can order 50lb blocks from Crayola or 100lbs from Dow. See http://vern.com/putty/ for more info.
Slashdot editors can't even check facts on Silly Putty stories. Sad.
The latest Slashdot meme.
WRONG!!! Its missing Silicon! It is a fake recipe!
:
Real silly putty does not dry out or leave much of a residue and is of course feshy-colorred.
Real silly putty has alwasy been
65% dimethyl siloxane, hydroxy-terminated polymers with boric acid
-- 17% silica, quartz crystalline
-- 9% thixotrol ST
-- 4% polydimethylsiloxane
-- 1% decamethyl cyclopentasiloxane
-- ~1% glycerine
-- ~1% titanium dioxide
and of course you can manufacture it now, out of patent, but you have to be careful how you market it.
Or you can buy it from DOW in bulk for under 10 dollars per pound.
I am the first post that mentioned this and its 12:18 PM E.S.T. , so I can't imagine how something that I knew most of my adult life was not mentioned or corrected by ANYONE else. More amusing is that no one moderates on slashdot anymore even though technically all email accounts are mostly anonymous.
But for those that care. There is the CORRECT resipe , and its totally different than the poisonous one for mere slime the article mentioned.
I was a bit dubious to your military claims since the linked article only makes reference to an attempt to make a synthetic rubber. However, a bit of research on sillyputty.com shows not only that you are correct, but also lists the ingredients (boric acid and silicone oil) required to manufacture it. Read on for an excerpt:
1940 In the midst of World War II, the Japanese contine to invade rubber producing countries in the Far East, cutting off supply to the United States. This begins to hamper war production efforts, especially for truck tires and boots. As a result, the government's War Production Board asks American industry to attempt to develop a synthetic rubber compound.
1943 James Wright, a Scottish engineer working for General Electric's New Haven, Conn., laboratory, combines boric acid and silicone oil in a test tube. The compound becomes "polymerized." Wright removes the goeey substance from the test tube and in his exuberance tosses some on the floor. Bouncing putty is born.
I'm a writer, a poet, a genius, I know it. I don't buy software, I grow it.
You can buy 5 lbs of silly putty for $60. Many people have done this before, and you can do some very interesting stuff with it. Like make a potato gun that shoots baseball sized balls of putty at brick walls. There are videos of this, and the putty ball shatters like a piece of glass because of its "silly" properties.
Its fun to do other experiments like bake it, freeze it, etc...
The recipe, well, at least the ingredients, are here.
As a followup to my own post, here is the correct Silicon full recipe
:
Preparing "Silly Putty", a silicone polymer (a methyl silicone, polydimethylsiloxane), via the hydrolysis of dichlorodimethylsilane with simple lab tools.
This silicone, which contains residual hydroxyl groups, will be cross-linked using boric acid (B(OH)3). This trifunctional acid forms -Si-O-Blinkages resulting in a peculiar type of gum. The commercial "bouncing putty" found in novelty stores is a silicon polymer with softening agents, fillers and coloring agents added. The actual full list of Silly Putty ingredients with colorants and softening agents is
-- 65% dimethyl siloxane, hydroxy-terminated polymers with boric acid
-- 17% silica, quartz crystalline
-- 9% thixotrol ST
-- 4% polydimethylsiloxane
-- 1% decamethyl cyclopentasiloxane
-- ~1% glycerine
-- ~1% titanium dioxide
This putty recipe is similar and equally pleasing:
Day 1: This reaction must be carried out in a fume hood.
Wear gloves to measure 20 mL of Si(CH3)2Cl (MW = 129.06, density = 1.064 g/mL) in a dry graduated cylinder. Rapidly transfer to a dry 250 mL Erlenmeyer flask equipped with a rubber stopper. Si(CH3)2Cl2 reacts rapidly with moisture to produce HCl gas so make the transfer swiftly. To this add 40 mL of diethylether and hydrolyze by adding 40 mL of H2O dropwise. HCl gas is evolved in this hydrolysis step.
The addition must be made slowly at the beginning of the reaction or too vigorous an evolution of the HCl will occur. The ether component will be warmed up to its boiling temperature if H2O is added too quickly. It is a good idea to have an ice-bath ready to cool down the reaction flask if the hydrolysis becomes too exothermic. The first 10 mL addition of water is very vigorous but less so afterwards. After this initial quantity, you may increase the rate of addition. The product has a very strong odor; be sure to do this in a fumehood!
Separate the ether layer at the completion of the hydrolysis step by pouring the mixture into your 250 mL separatory funnel. Wash the ether layer 3 times with 100 mL (for each wash) of 1 M Na2CO3.
This step is done to neutralize any residual acid remaining in the wet ether solution. Vigorous evolution of CO2 gas is observed at this stage as the neutralization proceeds. Add 10 mL more of diethylether to the flask after the first wash. Finally, perform on additional wash with 100 mL of water. Dry the ether solution over anhydrous magnesium sulfate in a stoppered Erlenmeyer flask, which you let rest for step two.
Day 2:
Decant the ether solution, filtering off any magnesium sulfate, into a pre-weighed 50 mL Erlenmeyer flask and evaporate off the ether using a water bath - not a hot plate. Note the yield of the dimethylsilicone oil (you should have approximately 9.5 g of material).
Add about 5% (by weight) boric acid (about 0.48 g for a yield of 9.5 g of oil), stirring continuously during the addition and for a few minutes after. This will cause the oil to become very viscous.
Heat the mixture to about 170-180 C in an oil bath and leave at this temperature for 2-3 hours. Allow to cool and remove the product from the flask by scraping it out with a spatula. If the gum is somewhat brittle, continued kneading will produce the desired gum-like characteristic. Once the gum has been removed, clean your Erlenmeyer flask with methanol.
Perform and report on the following tests:
(1) When rolled into a ball, does your product give a lively bounce on a hard surface?
(2) Does pulling sharply cause the gum to cleave?
(3) Does pulling slowly result in a stretching reminiscent of chewing gum?
(4) Does your product flow into a flat plate when placed on a flat surface?
(5) Is print transferred to the gum when test (4) is conducted on a flat newspaper?
General References
1. J. E. Mark, H. R. Allcock, R. West, Inorganic Polymers, Prenti
I think this was on /. before, but couldn't find the past story.
The Elmber's Glue recipes don't make actual silly putty. They make some cheap nasty knock-off that creates a silly putty-like compound that is slimey, leaves a greasy mess on anything it touches. Not only that, but this putty goes bad over time, unlike the real silly putty, which never dries out or gets moldy.
There is a recipe for making the real silly putty compound, but it is far more difficult and requires ingrediants and tools not found in a grocery store.
So what would happen if you dropped a head sized or larger amount of silly putty from three stories up? Would it bounce or would it splash? Or would it pancake? Has anyone actually tried this?
Impersonating Tycho from Penny Arcade since before there was a PA.
I had my students make this one time -- I was teaching a class on polymers. I had seniors in college playing with glue and boarx like little kindergarteners. Hah. They enjoyed it and learned something about viscoelastic polymers in the process, so I think it was all good.
Anyway... while fun, the stuff isn't really Silly Putty (R). That's a silicone polymer. The poly(vinyl alcohol) that's in glues these days does a pretty decent impersonation, though. You'll notice that it does feel and act differently, and it tends to dry out much quicker than the real stuff.
Just in case anyone cared on this obviously slow news day.
I'm suprised that among all slashdotters, nobody mentionned this. I think it's probably Silly Putty (TM) with more intense properties.
my 2 cents
Here we go again!
Yeah, hahahah, heh, heheh, wooo.
Thank god for that. I've finally stopped laughing. Took me 30 minutes though - take care clicking on that link if you've got to do something soon.
Get your own free personal location tracker
www.puttyworld.com
I have been waiting for a chance to post this like I found several years ago. Ever wonder what happens when you drop 50 lbs of silly putty (from Dow chemical) off a 6th(?) floor parking garage? Well you too can find out at Silly Putty Physics Experiment. Complete with medium and large video (actually the video is about all there is to the thing). Just like McDonalds and Starbucks, there is no "small".
The stuff described on the U Minn site is NOT the real Silly Putty. The real stuff is a silicon polymer as far as I know. The Elmer's Glue/borate mix has only a limited shelflife. It has some viscoelasticity, but it does not behave fully like the real Putty.
... the structure of silly putty is well enough known to be publicised in several introductory-level organic chemistry texts I have seen, and it is not too hard to reproduce.