Slashdot Mirror
Advice for a Novice Replacing Laptop Hard Drive?
frugalRepairs asks: "The hard disk in my Sharp PC-MV12W laptop recently died. It gave me warning and I had everything backed up. It was out of warranty and the repair folks want an arm and a leg to fix it. I would like to replace the hard drive myself but I've never done anything like this before. It seems to me that I would just extract the old hard drive, note the physical measurements, purchase new hard drive, and install it. However, I'm expecting Mr. Murphy to visit me as soon as I open the case and would like some advice from Slashdot experts. Do I need special tools? Does the BIOS have special needs? Are all 2.5" laptop drives created equal?"
As with desktop hard drives, yes, there are subtle differences between laptop hard drives (LHD) but basically, yes, all laptop hard drives are the same. While desktop hard drives are 3.5", LHDs are 2.5". The only tricky part is thickness - some older drives are 12mm and newer ones are 9mm. You can't go wrong with a 9mm, so just get that kind.
There are no bios issues to worry about. Plug in the drive and go.
Whether or not you need special toold depends on the manufacturer. I've only ever needed a philips screwdriver for my compaq aero, fujitsu lifebook, and dell inspiron.
Knowledge is valuable. Ignorance is dangerous. Censorship is unacceptable. http://slashdot.org/comments.pl?sid=10
Have you ever opened up small electronics before? A CD player or the such? The best approach is to do an amazing job keeping track of which screws go where, because they're all likely different. Additionally, every piece you take off will likely have a very fragile ribbon cable with a very fragile connection, so just be careful. generally the ribbon cables pull out once a small catch is slid towards them.
;) then power up, and so long as everything works (including, and double check this one, the fan) you're golden.
As for the actual hard drive, the bios in all recent (since they went to ide) laptops is completely compatible. Unless you've got a strange laptop that did what compaq desktops used to, with bios-on-disk, but sharp's aren't like that afaik.
Last thing... all 2.5" drives are not the same. My portege has a 9mm thick drive, and the new portege's and thinkpad x's take like 7mm or something. the standard i believe is 12mm, so you'll likely need one of the (slightly) more expensive models. Get a new one, as anything used could be just as broken as what you're taking out, and believe me its not worth it to pull that thing apart twice!
If you kept track of everything (screws, cables, etc) and nothing's left over
Good luck, and make sure you aren't over-tired or hungry when you attempt it, it can be frustrating.
Usually, the hard part is opening the laptop to get to the drive. There are many screws, but not all need to be unscrewed. Many parts are simply clipped together. I have opened several noteboks, and usually found out only too late that it would have been much easier if I had known how to open it.
First, try to search the web for a service manual which details how to get to the drive on your specific model. If you find clear instructions, that will be of great help.
For the drive thickness issue, as others have said, the recent thinner drives will work to replace older thicker drives, so you shouldn't have a problem.
If the notebook is old, the BIOS may not support the full capacity of your new drive. Not a big deal: you would just loose a few Gigabytes, but the drive will work perfectly with the lower capacity.
There are differences between drives, but as with desktop 3.5" hard drives, they're minor. You might not notice most of them. Plus, most of the drives sold these days have broadly similar specifications.
;-) Along with heat comes power consumption, which may a particularly important issue to laptop users since portables may often be running from battery -- on the other hand if you mostly use the computer plugged in on a desk, this might not matter to you. Spinning a metallic disk at X RPMs is a very serious draw on your battery. If you use the computer on your lap or running from battery try to compare manufacturer's power requirements.
Here are some of the differences you might want to keep in mind:
Physical size, as other have noted, is the most critical difference. Your laptop probably requires a 12mm drive or smaller, but make sure before you buy one. Old 2.5" IDE drives could be as big as 18mm! New ones are usually 9.5mm or 9mm.
Speed varies between drives: 4200, 5400, and now 7200 RPM drives are available for laptops. 5400 and 7200 RPM drives usually have better transfer rates and seek times, but may consume more power...but might not in comparisons between all drives. Check the drive specs. Like desktop drives, cache size also varies. Most models have 2MB caches, but some have 8MB, and this can affect both read/write speed and power consumption. The larger cache probably won't affect the cost of the drive very much, but may speed up certain IO operations. I recommend the 8MB cache.
Power Consumption & Heat: Just as with desktop drives, 2.5" laptop drives can generate considerable heat. It's harder, however, to get rid of heat from cramped laptop interiors than from desktops, and laptops may, errmmmm, generate certain heat related issues that would be a problem with a desktop under only the most contrived and embarrassing circumstances...if you know what I mean.
Noise: Hard drives can be the chief source of noise in laptops. Old drives with mechanical bearings will often be distractingly loud. This can be a problem during meetings or when working in a otherwise quiet office. Fortunately many newer drives have fluid bearings and are very, very, quiet. Definitely look for a drive with fluid bearings.
Capacity: 2.5" hard drives come in a variety of capacities. I'm sure you're shocked to hear that! The largest laptop drives I'm aware of are 80GB. You can still find 10 and 20GB drives for sale new, but prices are rarely significantly lower than for 40GB drives. A pretty reasonable price on a 5400 RPM 40GB drive is probably in the vicinity of $80. A drive with twice that capacity will probably be a bit less than twice the cost, but you'll pay a noticeable premium for a 7200 RPM drive.
As for manufacturers, I'm fond of Hitachi (formerly IBM). I've purchased at least a half dozen IBM & Hitachi 40GB drives with fluid bearings, in both 4200 and 5400 RPM versions, and haven't been disappointed yet. They are marvelously quiet, reliable, fast, and efficient. On the other hand, I've been so happy with them that I haven't bothered to check out competition from other manufacturers so my opinion may be out of date. And like I said at the beginning of the post, you're likely not to go too far wrong with any drive as long as it physically fits, since most manufacturers offer devices with broadly similar capabilities.
Good luck. I don't think you'll have much trouble.
you COULD have some issues with your laptop not recognizing the entire drive.
Actually, as long as he uses a reasonably recent OS (windows or linux) he shouldn't have any problems. Most modern OSs speak directly to the HD controller, bypassing the BIOS, and are therefore only limited to what the OS can support.
As other have pointed out, since you have a 40GB drive in there, pretty much any modern drive you buy will likely be ok as a replacement. The fun part then is actually replacing it. You'll either find it's easy, like most laptops from Acer, Toshiba, Dell. Or as hard as hell like anything from Apple (except the 15 inch TiBook).
Since it seems to be a sub-note, I wouldn't be surprised to find its the second one, but you might be lucky.
Generally, take off any panel on it which is only held on by 1-4 screws and look for something that looks like a laptop hard drive. Look also for little plastic tabs to pull on to remove it if there are covers on the side. Also, philips screws are a good sign for finding the hard drive. Torx bits are engineer's way of saying "here be dragons".
Good luck.
Use a digital Camera to take pictures as you go along. That way you will have a guide to putting it back together.
Use a muffin pan or cupcake pan to keep track of the parts. It is often hard to tell which screw is which so put them in different compartmants
Take notes.
Use a large work area set the parts down in a way that makes sense
Make sure you have time to do the job from start to finish. If you have to stop part way thought to go to work, you may forget something. Alternatively, someone may clean up your work area.
It may seem a little foolish at first but if you can't put it back together, WHO's the FOOL NOW?