Slashdot Mirror

← Back to Stories (view on slashdot.org)

Custom Motherboards?

Posted by Cliff on from the when-everyone-else-just-isn't-good-enough dept.

Druegan asks: "I've been rooting around on the net lately checking out all the latest and greatest in new PC parts, plotting out the design for my next build. I'm finding lots of neat stuff, but I can never seem to find a main board that has just the right combination of features. Therefore, I want to Ask Slashdot: Is there any way your esteemed readership knows as to how a person might get a main board custom made?" "I don't know how practical this is, BUT I'm looking for a mainboard that supports a dual processor configuration for the AMD64 FX 55 processor, built around the nVidia nForce 4 chipset. I'd like two full x16 PCI-express slots with support for the nVidia SLI, as well as room for at least 2gb of dual channel DDR, and SATA Raid support. I also am looking to be able to overclock the bejeesus out of the whole mess.

This is only a test case, but there currently is no such mainboard available. I'd like to know if there is some way to get one custom built though, even if it is ridiculously expensive.. (yes, this might fall into the 'more-money-than-brains' dept.)

I'd just like to build the system to see how it'd work."

39 of 120 comments (clear)

  1. Doy by Apreche · · Score: 4, Informative

    The reason that you can't get a board that meets your needs is because your needs are unmeetable. IIRC the Athlon 64 FX can't be paired in a dual processor configuration. That's what the Opterons are for.

    However, if you come up with requirements for a motherboard that are possible and you want to have one made, good luck. There are many companies that can do it for you for an extremely large pile of money.

    --
    The GeekNights podcast is going strong. Listen!
    1. Re:Doy by OAB_X · · Score: 2, Informative

      It cant be paired, you need the operton 2 series. Its basically the same as an FX, just with it being able to be used in multi-cpu configs.

    2. Re:Doy by davez0r · · Score: 2, Informative

      when you said "it's basically the same as the FX", i'm reminded of my dual athlon XP computer from a couple of years back. AMD said that you need athlon MPs for SMP. but the MP and the XP were essentially the same processor. the only differences were that the MP had added testing done, and the XP had some traces cut on its surface to prevent SMP capability. some conductive paint fixed that. is that the case here? or does the opteron actually have additional functionality that the FX physically lacks

    3. Re:Doy by scheme · · Score: 3, Informative
      when you said "it's basically the same as the FX", i'm reminded of my dual athlon XP computer from a couple of years back. AMD said that you need athlon MPs for SMP. but the MP and the XP were essentially the same processor. the only differences were that the MP had added testing done, and the XP had some traces cut on its surface to prevent SMP capability. some conductive paint fixed that. is that the case here? or does the opteron actually have additional functionality that the FX physically lacks

      Yeah, the 2xx opterons have the capability to setup a single coherent hypertransport link. You need coherent hypertransport links to get processors talking to each other without managling each other's memory.

      --
      "When you sit with a nice girl for two hours, it seems like two minutes. When you sit on a hot stove for two minutes, it
    4. Re:Doy by DetrimentalFiend · · Score: 3, Insightful

      I'd hate to say it, but this Ask Slashdot is retarded. The most pci express channels that I've seen any consumer chipset support yet is 20x, and 2*16 = 32. Soon, there should be dual core FX's, but you'll need to go opteron if you want dual 64bit cpu's. That much ram is no issue and can be found on nearly every mother board, but this guy FOR SURE has more money than brains.

    5. Re:Doy by sharkey · · Score: 2, Interesting
      The most pci express channels that I've seen any consumer chipset support yet is 20x, and 2*16 = 32.

      Tyan offers a dual-Opeteron board with dual x16 PCI-Express slots. http://www.tyan.com/products/html/thunderk8we.html

      --

      --
      "Outlook not so good." That magic 8-ball knows everything! I'll ask about Exchange Server next.
    6. Re:Doy by cavemanf16 · · Score: 2, Funny

      Indeed. In fact, he's not even concerned about the SLOWEST component of the entire system: the hard drive! Get a custom-built 20,000 RPM hard drive and the entire system moves faster. Get that 2GB of memory cached on board the CPU chip die and the system moves faster. He just wants to throw money at a poor solution to his computing "needs" to compensate for his less than l337 computer hacking skills. He should just resort to having num-chuck skills and be happy.

  2. I don't think that will work by Jjeff1 · · Score: 3, Informative

    Someone check me on this, but the FX series of chips don't support dual CPU.

    And the Nforce 4 isn't a dual CPU chipset. So you'll never find what you're looking for.

    1. Re:I don't think that will work by OAB_X · · Score: 2, Informative

      You would need a nForce Pro 4 chipset ofor dual CPU.

    2. Re:I don't think that will work by MerlynEmrys67 · · Score: 2, Informative
      Actually - the PCI-Express Chipset for AMD (The NForce) IS just a HyperTransport - Device chip... It will work for either a single, a dual, a quad, or for that matter an 8 way motherboard.

      You can have two of them in your dual proc system (or 4 of them for that matter) and get your multi 16x.

      Don't look for any manufacturer to produce such a thing, and frankly - doing a custom motherboard is probably out of your reach unless your first name is Bill and you don't mind throwing down a few million for a custom job

      --
      I have mod points and I am not afraid to use them
  3. Cool. by TsukasaZero · · Score: 3, Funny

    Enjoy your new, non-realistic, motherboard.

  4. What's the production run? by Anonymous Coward · · Score: 5, Informative

    Unless we're talking about thousands or tens of thousands, it's not economically viable. This is not a system-on-chip design, so it requires considerable debugging. Prototype manufacturing costs are always high as well.

    My advice as an electronic engineer: give it up, your idea doesn't make sense.

    1. Re:What's the production run? by harrkev · · Score: 4, Informative

      What the parent says is correct, but let me elaborate. Let's assume that you DID have the knowledge and education to undertake this. Here is what you would need...

      1) A complete schematic capture system with a really good board layout tool. My company provides one for me, so I do not know how much they paid. But I would guess that for one license, you would have to spend $10K or so. Certainly more than $5K. Note that there are budget packages out there ($2K or so), but you get what you pay for.

      2) You will need to get the board manufacturered. Expect at least $2K or so for a handfull of boards (probably closer to $5K). Since you will not get it right on the first try, you will have to get multiple revisions made.

      3) Buy parts. Some items have a minimum buy quantity. You might need to get entire tape-n-reel packs.

      4) Get the board built. This is not something that you can do yourself, unless you have $100K equipment lying around. Contract this out. My best guess is between $1000 and $5000 for small quantities. I am not sure about this part, though.

      5) Debug. You do have test equipment, I hope. Minimum equipment will be a good logic analyzer and oscope. The minimum that I would recommend would be an Agilent frame with a good analyzer card, pattern generator card, and o-scope card (tektronics make awesome scopes, but I do not like their logic analyzers). Expect to drop at least $30K on this. You can rent, though, if money is tight ;) Now, if you want to make your job easier, you might want to get some specialized equipment. Special analyzers exist which analyze one type of interface. You should probably have one for HyperTransport (assuming AMD), one to analyze the DRAM channels, one to analyze PCI, one to analyze USB, etc. You get the idea. This stuff will be used a lot less, so you should rent it.

      6) Let's assume that the hardware works. Did you want a BIOS with that? License it. I have absolutely no idea how much this costs. You will likely have to costomize the BIOS for your board. You might be able to do this with open-source tools. Expect to spend some time on this, though.

      7) You want that done this year? While you hold down a day job? Expect to spend $10/day on no-doze and Jolt cola.

      As you can see, there is a LOT involved. The only reason that you can get a motherboard for $100 or so is that they make a LOT of them. The first motherboard is incredibly expensive. The second one is dirt cheap.

      --
      "-1 Troll" is the apparently the same as "-1 I disagree with you."
  5. I'm your man. by CarnivoreMan · · Score: 3, Funny

    Go ahead and pay me $10,000 to my PayPal account and I'll get started right away. It'll be in the mail real soon! I can even through in a nucular mobo battery and wire it with a turbo button.

  6. I believe that the Tyan .... by the+eric+conspiracy · · Score: 3, Informative

    has something very close to what you want in their Thunder K8WE. You need Opterons though because the AMD64 doesn't support dual CPU, and the chipset is the NVIDIA nForce(TM) Professional 2200 and 2050 series, which is needed for dual CPU and PCI-X.

  7. Not a good idea by photon317 · · Score: 4, Informative



    Aside from what others have already pointed out, namely that your chosen CPU and Chipset don't appear to support dual processors to begin with, the idea of having a custom motherboard made is silly.

    Motherboards are extremely complex peices of equipment. An enormous amount of work goes into getting them production-quality, it's a lot more than just wiring the rights pins of the right chips and sockets together. There's all the EMF and heat effects to consider, trace lengths and their effect on signal propogation, etc. Then ocne you have a baord that's even capable of functioning reliably, you have to make a BIOS for it and get all the right parameters tweaked correctly to initialize the board the right way - there's a lot of values tuned by the vendor for the board in question that you never see in your little BIOS setup screen.

    Even among commercial boards, as we've seen on review sites, there are varying levels of success at building a rock-solid stable board. It requires an enormous amount of engineering man-hours to go through the design and testing process, and sometimes they still can't get it quite right, and half the boards are a little "flaky" under the wrong conditions.

    So even if you wanted to drop some enormous sums of money (very enormous, I would imagine, orders of magnitude more than the cost of any custom built PC), it would be unsupported by other vendors (drivers, etc), and likely be plagued by little one-off problems like so many new boards are. Usually the vendor can see the trends in the problems based on numerous end-user bug reports, and fix it in the BIOS - but with just one user, good luck.

    Chances are that if you actually made a competent choice about what motherboard features and components really suit your needs, you'd find they already make it anyways.

    --
    11*43+456^2
    1. Re:Not a good idea by forkazoo · · Score: 3, Interesting

      Uhh, This is one of the hundred or so "me too posts." The Asker has no idea what he is doing.

      That said... When I glanced at the headline, I assumed it was about somebody doing a custom 8 bit or 16 bit system, and was looking for some resources to make his tricked out Zilog box look more professional.

      So, I'd love to hear from some experts about just what level of custom board would be doable for a hobbyist? How about a dual 8080, or maybe (joygasm) a dual 386 custom board? What free/cheap tools are available, and who does cheap low-volume PCB runs? Let's all pretend that a useful question was asked, and answer that!

    2. Re:Not a good idea by HeyLaughingBoy · · Score: 4, Informative
      So, I'd love to hear from some experts about just what level of custom board would be doable for a hobbyist?

      Depends on your definition of "hobbyist."
      I'm an electrical engineer who also does hardware/software design & development both as a hobby and for pay as a side job. You can build pretty sophisticated hardware these days: it's never been easier.

      I use the free version Eagle CAD to do PC boards under Linux, and there are plenty of shops that will build prototypes for under US$100. Most of the important parts manufacturers will either give you free samples, or sell small quantities off their website. My compiler of choice is gcc, also free.

      My biggest problem is usually coming up with a cool project that's (a) worth doing, (b) doesn't cost an arm and a leg, and (c) can be done by one person who's married with a small child in less than a lifetime (i.e., 6 months or so :-)

      As a result, my most interesting projects tend to be from the people who pay me to design something they need, but have no idea how to do.: generally people with plenty of expertise in fields other than electrical and software engineering.

      The stuff I come up with on my own tends to not get finished; OTOH, knowing someone's waiting on me to deliver (and is paying) is a huge motivator to get done on time.

      HTH :-)
  8. Tyan Thunder K8WE by DeadBugs · · Score: 5, Informative

    http://www.tyan.com/products/html/thunderk8we.html

    - Dual AMD Opteron(TM) 200 series processors
    - DUAL PCIe x16 with FULL SPEED x16 lanes
    - (8) DIMMs for Reg'd DDR400 memory
    - U320 SCSI and SATA-II with NVRAID(TM)
    - Dual Gigabit Ethernet with ActiveArmor(TM)
    - FireWire and USB 2.0 ports

    --
    http://www.kubuntu.org/
    1. Re:Tyan Thunder K8WE by MerlynEmrys67 · · Score: 2, Insightful
      DUAL PCIe x16 with FULL SPEED x16 lanes... no, those are PCI-X slots, not PCIe.
      Try again. Those are dual PCI-Express x16 slots. You will notice 3 chips on the motherboard (well, you didn't since you obviously didn't go to the website where these claims are made in plain english - with a picture that shows the slots as well) - two chips are HT-PCI express chipsets, the 3rd is a HT-legacy chipset giving you an additional set of 2 PCI-X 100 and 1 PCI-X 133 slots

      Thank you for playing - come again

      --
      I have mod points and I am not afraid to use them
  9. I can by Anonymous Coward · · Score: 5, Informative
    Give me lots of money and time. I will need to learn all about the processor's power requirements, the connection to all the other chips, their power requirements, their datasheets, until I know everything about every part that's gonna be needed.

    Then you need to pay a licence for a schematic-capture to PCB suite with simulation and auto-routing. I think a few 100K$ for the Cadence suite should do it. Oh, you thought that someone who thinks two-layer boards are a challenge and uses Eagle could do it? Nope.

    You'll need someone to procure small quantities of the parts you want, that is, get to know all the reps in your area and squeeze them for samples. In between the badgering phone calls, you still have to order all the other parts, while trying to find a local PCB assembler to handle your parts. Don't forget to supply the pick-and-place file and keep in mind the constraints when building your parts library. Oh, you thought you can just buy parts and the software automatically draws them for you with the IBIS model already connected? Nope.

    Advise the fab of your PCB ahead of time of the layer count and size of the PCB so they can at least get the materials and open up a time slot for you. When you start the layout, you should be able to estimate a completion time, so it's not a problem, right? You did think of the stack up BEFORE laying out, right? You didn't just use any thickness you felt like, right? You know the difference between pre-preg and core, right?

    Anyways, once you've done all the placement, assigned all the properties to the nets (unless you did all that on the schematic and configured the packager to forward the properties to the board), set up the DRC rules and routing areas and keepouts, and defined your via technology, and routed the critical paths, you can unleash the auto-router.

    While Specctra is churning away, you can go back to the BOM. Are all your parts going to ship at the same time? Will you receive them at the same time? Will you ship them to your assembler or will you want to look at them first? Anyways, you should be able to tell them when to open up a slot for assembly so they can schedule it.

    After the auto-router is done, it's clean up time. Check the artwork carefully. Create the assembly drawings, mechanical drawings, drill files, pick-and-place and IPC files. You *will* want to electrically test the PCB before tossing it to your assembler, right?

    So the layout is done, you can start sending gerbers to your fabricator for DFM checking, and you can send the pick and place and solder stencil files to the assembler. While the DFM checking is done, you can extract the layout into Signal Explorer and run some simulations to see if there are any signal integrity issues. What's that? You want to run those tests BEFORE actually getting the board built??

    Well, it's already been a year since the project started, and no one can wait anymore....

    Dude, what you're asking for is the single most ridiculous thing I've ever heard on /. Even more outlandish than the "can I use a laptop LCD on a desktop?"-type questions.

    1. Re:I can by John_Booty · · Score: 5, Informative

      "Dude, what you're asking for is the single most ridiculous thing I've ever heard on /."
      -----

      I agree completely.

      I've been posting on Slashdot for around 7 years and I think this is my first "me too"-style post. Please forgive me. It's just that this question was so. fucking. ridiculous. Literally the stupidest thing I've ever seen posted on Slashdot.

      --

      OtakuBooty.com: Smart, funny, sexy nerds.
    2. Re:I can by amigabill · · Score: 5, Funny

      >Dude, what you're asking for is the single most ridiculous thing I've ever heard on /.

      I'd like an Amiga laptop computer. Now that I just made this guy look totally sane, go get to work and build his totally sane motherboard for him... :)

    3. Re:I can by Anonymous Coward · · Score: 3, Insightful

      Read some of his other posts - he's wondering why he's having problems breaking into IT. Maybe it's because he's so utterly clueless. Maybe.

  10. Buy some stock. by jamey.v · · Score: 3, Funny

    The only way I could see this happening is if you bought a controlling interest of a MB manufacturer stock. Think of it as an investment.

  11. ridiculously expensive by j-turkey · · Score: 4, Insightful
    even if it is ridiculously expensive

    You're asking for quite a bit. A few people here have pointed out that FX 55 does not support a multi-cpu configuration (so you're already asking for a custom CPU/chipset), however, taking it a step further, the development process that goes into hardware development (especially for mainboards) is astounding. From reference chipset design (as well as testing and manufacture), to OEM's implementing that design (again, testing and manufacture). It's a big deal, and the process costs millions from end-to-end.

    If you can afford this kind of solution, and are willing to take it on for personal use, I think that you're right that the discussion is quickly exceeding the more-money-than-brains department and entering the more-money-than-god department. Hell, if you can justify the cost of not only one, but two FX55's for a personal machine, you may already be in the more-money-than-brains department.

    Check out the AMD roadmaps at Anandtech.com. You may just want to wait for the next FX chip release with dual cores, and an NF4 SLI nForce chipset. The dual core chip is as close as you'll get to true SMP, SLI will provide your 2 x16 PCI-e slots, the NF4 will provide support for dual-channel memory. These systems also come with SATA raid support, but IMO, an external controller is best (especially if you can find one with a battery backed cache). You'll have plenty of cash leftover for a badass liquid cooling system to overclock the crap out of that sucker. You will lose the exclusivity of having a super-custom system that nobody else can get, but hey -- it'll still be badass, and you will save $millions over custom hardware development.

    As an alternative, if you're after exclusivity, you can start a hardware review website, gather a large readership, and then ask manufacturers for pre-releases of the latest greatest hardware for testing purposes. You'll get better-than-consumer support, and will have a machine that none of your friends will be able to buy for at least a few months.

    --

    -Turkey

  12. dude by Anonymous Coward · · Score: 5, Funny

    you're a retard. custom motherboards..? what do you want next? a girlfriend?

  13. Re:Really hard... by Anonymous Coward · · Score: 2, Funny
    "Not even double sided boards would work"

    You just made my day! That's one of the funniest examples of "n00b miscalculation of complexity" I've seen in a while.

  14. easy answer by jenkin+sear · · Score: 2, Funny

    The easy answer- just buy ABIT. Not the board. The company.

    --
    What a strange bird is the pelican, his beak can hold more than his belly can.
  15. Dear Slashdot by justforaday · · Score: 5, Funny

    Dear Slashdot,

    I'm looking for a videogame system that will play every game that's ever been made out there. I don't care how much it costs. I want it to be able to play every imaginable format, all through a single universal slot. Oh, and it can take any sort of controller ever made too. And while you're at it, make sure it can play every type of audio and video format (I'm planning on using it for my 1337 home theater setup). And don't forget to make sure that it'll be able to play everything that comes out in the future, too. I realize I may be asking a bit much, but I'm pretty sure it's doable...

    --
    I'll turn into a supernova and burn up everything. Well I'll turn into a black little hole and you'll turn into string.
  16. What in the hell. by Anonymous Coward · · Score: 2, Insightful

    Earlier this morning I posted a very serious "Ask Slashdot" regarding getting advice on requirements for a remote "store and forward" system I'm trying to design for physicians in very remote areas of third world countries. It's good to see that my topic gets ignored while ass-drippings such as this get air-time.

  17. For the price of a custom mainboard... by NoMoreNicksLeft · · Score: 2, Interesting

    He could easily afford a x8 or x16 cpu machine from a big vendor. One that has been thoroughly tested, rather than an engineer's first prototype. With his pick of actual SMP-capable cpus, no less.

    So how about a less dumb motherboard question?

    Q) I need as many PCI slots as possible, with at least a few being 64bit. 4-6 slots isn't nearly enough, I'm a guy that could fill 10+ easily. And a few (read:2-3) ISA slots would be nice also.

    I'm not so picky on other things, but a wishlist in order of priority is as follows:

    #(10+) PCI slots
    dual cpus
    64bit cpus
    amd cpus
    dual onboard gigabit
    #(1-3) isa slots
    dual onboard serial ports

    I think that a passive backplane is the answer I'm looking for. Things like the Magma PCI expansion system (where 7 pci slots sit in their own rackmount case) aren't quite what I need. I understand enough about backplanes now, to know that I need a PICMG single board computer. Is it the right answer for what I want?

    What price range are we talking, working up through modest configurations, up to the ones that meet all of my wishlist items?

    Am I overlooking some other (presumably lesser known) options that would meet most of these needs?

    Are there any pitfalls in installing and using linux on such a system?

  18. While we're at it... by perfectlynormalbeast · · Score: 2, Funny

    ... I could use a custom CPU. Since I'm left-handed, I'd like something like an athlon64, but the leftshift instruction should shift right and the rightshift instruction should shift left. I'd be willing to pay an extra $50 for that!

  19. Go to Taiwan by Matt_Bennett · · Score: 2, Informative

    Seriously- if you wanted to build your own custom motherboard, do what the big guys do- go to one of the motherboard makers in Taiwan. You'll need them because they already have relationships with all the CPU and chipset companies. You (or the company that makes the motherboard) would very likely have to use something already released, or enter into some *very* restrictive NDAs to get pre-release silicon, and that would be only if you can convince the silicon manufacturers that they should use up some of their very limited pre-release silicon on you and your project.

    It will cost millions and take 6 months to a year to get a good, stable system. Making a motherboard is far from the "just plug it in" stage, particularly when you get to new-ish technology (say, stuff released in the last 3 years). Everybody is still learning how to connect things up right and view the secrets of the development and testing as proprietary.

    On the other hand, there is a big problem in what you're asking for- as far as I am aware, The chipset you specify doesn't support 2 x16 PCI-E slots, and opening it up to other chipsets, there are none that offer capability for 2 x16 slots (available now)

  20. Here is how you do it. by LWATCDR · · Score: 4, Insightful

    1. Contact AMD and have them fab you a pair of FXMP chips.
    2. Contact Nvidia and have them make a custom nForce4 chipset that supports MP and 32+ channels of PCIe
    3. Contact Asus and have them fab you the actual board.
    4. Contact Award for the custom Bios you need.
    5. Enjoy your custom MB and you claim to the title of King of the mods.
    Total Cost... about 1 billion dollars. Okay maybe not but many million.

    Good grief how did this make it on Slashdot?

    --
    See my blog http://ilovecookes.blogspot.com/ for light hearted technical information.
  21. Re:Really hard... by Anonymous Coward · · Score: 2, Funny

    Wow. You mean you can't just buy a resist pen and blank copper-clad at Radio Shack and do your own motherboard? Who would have guessed! I guess you could go reeelly high-tech and wire-wrap it. Just need to pind a CPU thats in a DIP package.

    Sorry kids. This is only funny if you're over 30. Just humor me.

  22. The short version by fm6 · · Score: 2, Insightful
    Put it another way: it costs almost as much to build one motherboard from a particular design as it costs to build the thousands (anybody know a more precise figure?) as it costs to build just one.

    It's sort of ironic: most of us depend for our livelihoods on the fact that computers are cheap. Computers would not be cheap without economies of scale. Yet few Slashdotters seem to grasp the concept. They're always complaining that nobody bothers to port their favorite game to Linux or Mac, or that off-the-shelf hardware never has the precise feature set they want. Or that they can't save money by ordering hardware that lacks commmon features they don't want.

    Econonomies of scale explain why Sun is in trouble, and Bill Gates is the richest person in human history. It even explains why Enterprise was cancelled! People really need to understand the concept.

  23. Start taking basic electronics classes ... by bergeron76 · · Score: 2, Insightful

    After a few years, you might be able to build an embedded system using an ARM processor or something. From there, you'll couple your USB, etc. chips.

    In about 10 years you'll be able to create your perfect board, however, technology will have advanced so far underneath you that you won't be interested in such a board anymore.

    Basically, for all the work involved, it's not worth it. Buy 2 computers and get a KVM switch; or share the resources on a network, etc.

    But for heaven's sake, don't try to create your own desktop mobo - it's just not practical.

    --
    Don't think that a small group of dedicated individuals can't change the world. It's the only thing that ever has.
  24. Re:Three easy steps by PhraudulentOne · · Score: 2, Funny

    You messed that up...

    Step 1: Pay major mobo mfg about $1,000,000

    Step 2: Wait a long time for it to be built

    Step 3: Debt!

    --
    You create your own reality - Leave mine to me.