Slashdot Mirror
Massachusetts "Right To Repair" Initiative On Ballot, May Override Compromise
skids writes "MA voters face a complex technical and economic question Tuesday about just how open automobile makers should be with their repair and diagnostic interfaces. A legislative compromise struck in July may not be strong enough for consumer's tastes. Proponents of the measure had joined opponents in asking voters to skip the question once the legislature, seeking to avoid legislation by ballot, struck the deal. Weeks before the election they have reversed course and are again urging voters to pass the measure. Now voters have to decide whether the differences between the ballot language and the new law are too hard on manufacturers, or essential consumer protections. At stake is a mandated standard for diagnostic channels in a significant market."
As a classic car enthusiast, the only interface you need is your wrench set.
With this said, modern cars are designed to be off-limits for DIYers. This specific issue is about preventing locking down cars to the level that even independent mechanics can't touch them. So question should read "Do you believe that all cars, 2012 and newer should be only maintained at the dealer shops, or should independent shops have a way to do more than just change oil?"
Something's wrong when I have to dedicate a laptop, play $350 for a special cord and software, and teach my self this software just to 'adapt' my VW's throttle body?
BMW drivers have it even worst!
Federal legislative language should read that EVERY manufacturer that wants to sell cars in the US must allow owners to look at and function every aspect of their own car without special dealer tools.
If you can't sell something that contains coded information?
So are we saying vehicle diagnostics are a special case? Just diagnostic codes, or any private coding scheme anywhere?
It seems like a stretch, like maybe you should be requiring manufacturers to provide certain diagnostic capabilities standard instead of attacking the use of coding schemes directly.
Specialized tools are necessary for service work
This does not count as a "necessary" specialization of a tool:
If manufacturers must limit themselves to open, standardized interfaces they will be slower in achieving greater emissions and fuel efficiency.
[Citation needed]
It's time to accept the fact that the priority must be emissions and efficiency and not owner's liberty
Therefore, we should ensure that only mechanics who pay the maker of the car a monthly fee can perform repairs!
There is a logical step missing from your argument...
Palm trees and 8
Why should you have the right to do maintenance on a car that you probably do not own outright?
http://blogs.wsj.com/law/2012/10/29/supreme-court-grapples-with-copyright-law-and-the-resale-trade/
Prove anything by multiplying Huge Number times Tiny Number
http://www.warmglass.com/making_your_own.htm
"Kill 'em all and let Root sort 'em out"
No one says they have to limit themselves to those interfaces. They can just provide the specs and documentation. They have to this information already requiring they make it public is not a huge stretch.
You are just being a nutcase.
Specalized tools are necessary to remove half of the front end and 1/3 of the engine to change the frickin' oil.
der dee der.
I have a Sun Enterprise M4000 server that has the fault light on. In order to clear the fault light, I must run the "clearfaults" command on the service processor. You must get a special password from now Oracle in order to execute the command... I should be able to run the command myself without paying Oracle for a support contract.
Karma: Bad
I'm a MA voter. I read the law. It sounds like the data needs to be made available in a standardized and un-encrypted way for all future cars. If you have all ready conceded to making the info available, what is the problem in doing it in a non-proprietary way?
That was a rhetorical question. I'm voting yes.
Not that I don't agree with it personally it doesn't really affect me. I've always been able to track down whatever code I've needed on the internet. I understand an actual garage may not to want to rely on the internet for all it's needs, but for me personally just like I'll make due with the $20 Haynes and not the $800 Bentley manual I don't really need officially blessed. But then I'm not in the business either.
With a title like "Right to Repair", I thought I was going to be reading about another state trying to duplicate the purpose of California's so-called "Lemon Law", which literally is a 7-year right-to-repair mandate not just for automobiles but all mass-produced consumer goods with a cost over $100. In California, thus, manufacturers are obligated to make available the parts and documentation necessary to keep a product in service for no less than seven years.
This Massachusetts proposal seems to be a lot more limited and specific to vehicles.
Specialized tools are necessary for service work.
This is not true for a great deal of maintenance. Furthermore specialized tools are often not necessary if the parts are designed sensibly. Often the manufacturer has a choice when designing it and using a specialized tool when one is not needed is an attempt at lock in. Encouraging lock in and short-cut design is a bad idea always.
If manufacturers must limit themselves to open, standardized interfaces they will be slower in achieving greater emissions and fuel efficiency.
The logic of that does not compute. A well designed interface can greatly speed achievement of emissions and fuel efficiency standards. Standard tooling, electrical interfaces, etc can greatly reduce cost, complexity and allow engineers to focus efforts on more productive pursuits. Reinventing interfaces because of Not-Invented-Here is frankly rather stupid. Arguably using closed proprietary interfaces slows development rather than speeding it up in many cases.
Just saying what you lefties would say if you had the balls.
Ahh, I get it. You are a troll. My bad for feeding you...
Almost had me there. As is the norm, I started banging out a response before reading everything, such as the last line.
If the measure of Sarcasm is that you can't tell it from the real thing, then you are brilliant!
Bravo!
When Fascism comes to America, it will call itself Anti-Fascism, and tell you to give up your guns.
People take so much time complaining about "modern technology" that they have none left to learn how to deal with it. I work on cars as a hobby and I'm doing fine even repairing modern cars that dealers can't get fixed. Yes, I use my brain combined with old school skills to fix all sorts of cars, modern and classic. Modern cars aren't that more difficult to fix or diagnose, it just takes a decent understanding of basic electronics and mechanics. Modern diagnostic computer systems should be standardized, so independent mechanics and hobby workers can still afford to work on them. It has always required mechanical skills, knowledge and good diagnostic skills to work on cars and that should remain the same, even if you need some computerized equipment to do some of the diagnostics. If a dealer can't fix it, it's usually because they have bad diagnostics technicians working for them, not because the computers are making it difficult. They had the same problem 50 years ago, when cars didn't have computers or electronics and the same applies to hobby workers.
I was promised a flying car. Where is my flying car?
Six people so far who didn't read the whole post.
ROFLMAO!
And I bet the Mods didn't either.
When Fascism comes to America, it will call itself Anti-Fascism, and tell you to give up your guns.
"See, the Supreme Court just held up that "first sale" doesn't count if the *thing* was intended to be sold to a segregated market"
NO they didn't. They just heard the arguments. A conclusion isn't expected for several months. Stop glancing at articles and actually read them.
There is no state law preventing you from working on your car in your driveway. If there was then I know people who break it all the time, myself included. Their may be some town ordinances, but those are rare.
That said this is NOT about you fixing your car in the driveway. This is about giving local repair shops the information they need to repair your car. Dealer charge $65/hr local places usually around $45/hr. If the local guy can't fix it then you're strung up for another $20/hr.
VW upgraded my new car's diagnostics software. ALL shift points, RPM ranges and throttle positions changed resulting in a new car that drives nicely like an olde lady would expect. So radical was this upgrade that it changed the handling and performance of the vehicle to something I would never buy.
VW have refused to re-install OEM software back to the new car fitment. So MA are onto the NEXT contentious issue for consumers paying $$$ hundreds of dollars monthly for product they have absolutely no control except paying rents to manufacturers
I've never been busted for working on my car in the street in the People's Republic of Cambridge. In much of middle America your neighborhood owner's association is going to have rules against this; fortunately in a city if you don't live in a condo the only rules are set by people you can vote against if you disagree with them.
If manufacturers must limit themselves to open, standardized interfaces they will be slower in achieving greater emissions and fuel efficiency.
Just saying what you lefties would say if you had the balls.
Oh, so you are lying because you think that's funny. Got it.
Learn to love Alaska
This is not just about working on your car in a driveway. It is knowing if there is a problem, and if the problem need to fixed now or later, and what the fix should involve. For instance, my car will tell me when anything is wrong in many parts of the car, but when something is wrong in the engine, all that will happen is the 'check engine light'. Even with a scanner, and I have one for my talbet, there is precious little information to be had. The information should be there, but the car computer will not give it up. So when I take it to the shop i don't really know what to expect. Furthermore I don't know if I can take it to one of the 10 autopart stores around me and fix it myself(not in the driveway) or if I have to take to my mechanic, who is trustworthy, reliable, and not incredible expensive, which means there is also always a line.
"She's a scientist and a lesbian. She's not going to let it slide." Orphan Black
This is about getting error codes not tools. There's this diagnostics device you can buy at Autozone. You plug it in to the outlet under the dash, and start your car. It spits out an error code, and if you're lucky it spits out the problem, if you're lucky. More often than not that problem is something like a Oxygen Sensor. Something which takes 5 minutes to replace, and requires little or no tools, as it just clips onto a wire harness, and into the air filter. Cars (other than hybrids) haven't changed much, and neither has fixing them. If you're computer is bad, you get a new computer, and plug it in. It's not rocket science.
This is about having the information you need to go to the local parts dealer and buy the right part. Without the codes the local auto mechanics who own businesses can't fix the cars either, and end up guessing at what's wrong and wasting your precious money.
never own your vehicle = they have to cover all repair costs maybe even laws covering rented cars will be in there as well.
I run my familys NAPA AutoCare center and this year we had a 2007 Dodge Caliber come in with a customer complaint of one headlight not working.... Even after replacing the bulb.
Only one of my techs knew that the TIPM module had to have the circuit reset with our $4,000 + Snap on scanner.
Yes I have read that you can do something with the battery cables and I am also aware of reasons not to do this... At the end of the day, a computer was needed to change the headlight on this particular vehicle.. Kind of insane..
Doesn't that state also have a bunch of local ordinances that prohibit working on your car in your driveway or parked on the street?
-jcr
Nope. Not as far as I know.
This is the first I've ever heard of that and I've lived in Massachusetts all my life. I've worked on my car in the street with no complaints, and see others do it all the time. I don't see how you could ban *all* working on cars. If you've got a flat tire or a bad headlight, what would you be supposed to do? I could understand some communities banning oil changing on the street given the convenient storm drains for illegally dumping your waste oil, but I don't know of any that have. It's easy to dispose of used oil. Any store that sells oil is required to accept used oil for recycling, which I suppose is probably the national norm.
In any case, on-street repairs are not practical much of the year due to lousy weather. Most people would prefer to do the work in their garage if they have one.
Post may contain irony: discontinue use if experiencing mood swings, nausea or elevated blood pressure.
I am sorry, but by that logic all the lawnmowers, chainsaws, snow-blowers, etc. in the world should have highly sophisticated ignition systems with locked down ECUs. I think not. I think you are highly misguided, though your heart is in the right place. You can most certainly make an open system that is just as efficient as a closed one. This is all about exclusion and not improving emissions. Big business doesn't give a rat's ass about the emissions. All they care about and are legally required to care about is bottom line and shareholders' profits. If I can not repair my older car due to the stupid error codes in the ECU I need to go out and buy a new car and junk this one. I just made an environmental impact that far exceeds keeping the old less efficient car running. Get it?
Oxygen Sensor is the most wrongly oversold part in the auto parts business. WIthout the proper information or a knowledgeable mechanic this part will continue to be oversold again and again. And it's not in the air filter.
Most Oxygen Sensor sales the customer ends up returning for the 'real problem' later on. After replacing the computer (which wasn't bad either, they usually find a vacuum leak, or dirty MAF sensor, etc etc.
I made a good living servicing Selectric typewriters back in the 90s and uo to about 2002, entirely due to the court decision that forced IBM to permit independent servicers to purchase manuals, tools, and parts. And a little mechanical aptitude. Untimately it was about product owners being able to fix their own stuff, and engage whoever they wanted to. This decision had effects in other industries.
At the least, car manufacturers should be required to publish the specs for the diagnostic interfaces, and then sell the manuals (reasonable price was part of the IBM decision, IIRC) and let us service what we do in fact own. If they are claiming that the software is licensed, not sold, we need to have that fight.
FWIW, I drive a 1998 Saab 900 SET Convertible. What a fun car. If you hose up the top, for instance repositioning any of the potentiometers that feed back position data to the computer, you will be going back to the dealer or someone who purchased the very expensive Tech II tool, which is not just an OBD2 reader, but interfaces with various onboard computers and make settings etc. I've done some terrible things to the top so far, and no need to reprogram, but that's just because I was warned in advance. My local dealer gave me the radio code when I had the battery replaced - they didn't have to do that for free, but they did. I'm pretty interested in this, since I prefer to buy beaters, and soon there will be no such thing, just high-mileage cars that need trips to the dealer to solve specific onboard computer problems.And there will be more, not less. problems with this. Despite major improvements, I don't see these onboard computers getting that much better, and the automobile is a terrible environment for anything like that. With Saabs, the 9000 was notorious for problems figuring out just which computer was causing the error, and the TCS system would put you in limp mode at the drop of a hat. Perfectly good car, just the computer choosing to be broken. ABS, climate control, seats, top, etc, there are 7 computers I know of in the 1998 Saab 900, not counting ther SID and cruise control...
And Saabs, of course, are orphaned. Why would they withold info if there is no more business to protect? Mine can suffer any number of problems and that's the end of it, no part to fix it with. Windshield moldings seem to be gone now, so you use generic rubber. Parts for the top are becoming terribly precious.
deleting the extra space after periods so i can stay relevant, yeah.
Not really, no. A state could pass a law making it explicitly illegal to sell or rent a car that does not have full disclosure in place (with exceptions in place for individual owners). I suspect the disclosures would be forthcoming.
I agree--grand parent's assertion of "standardized interfaces they will be slower in achieving greater emissions and fuel efficiency" is complete bullshit. Citation needed like never fucking before.
I know cars and I like modern cars. I don't do well with carburetors. Give me a fuel-injected, electronically controlled system all day long. Give me a modern ECU that will automatically adjust for barometric pressure and ambient temperature. Give me an ECU that will give me good fuel efficiency and emissions. I race my car, but I do not remove my catalytic converter.
They don't want to expose the dealer interface for reprogramming a car's mileage, VIN inside the ECU or new keys w/o having the two existing keys. That's the entire extent of the security concern with the exposure of this information.
Otherwise, if my car is malfunctioning and I want to diagnose why it's not running right, I am all too often hampered or screwed without the dealer tools.
Simple example first: my car developed a knock in a cylinder. To find out whether it's a valve or a rod bearing or piston-slap, I have only one option: disconnect the ignition connector and the fuel connector, start the car, shut it off, etc repeat for each cylinder. However, the dealer can simply go into a menu and trigger an ON_1/OFF_1 (from 1 to 4) for each cylinder, doing the same thing electronically, faster and safer.
Complex scenario: diagnosing catalytic converter failure (which is very emissions relevant!) If the car is running rough or is down on power, especially top-end power, it's possible that this might be caused by a catalytic converter. However, many other things could also be wrong to cause this. The best you gonna do as a DIYer right now (for a 2004+ Mazda, in my case) is to wait until the computer throws a check engine light complaining of cat converter inefficiency. However, your situation might be right on the threshold of the rather-generous factory allowance for catalytic converter performance. The dealer can simply pull up a page of emission stats the the car tracks, which lists catalytic converter efficiency. If it's near the bottom of the range, especially for a car with lower mileage, then you have a dying converter. You can monitor this setting over time as well (E.g. over two weeks) and see if it degrades. Having access to this information can save you non-trivial dollars in gas mileage (e.g. highway can drop from 30mpg to 24mpg easily), fouled up spark plugs and (albeit small) risk of engine damage. Since most modern cars run spark plugs capable of long term replacement intervals, such as 60K miles, you risk fouling up an expensive set of plugs.
This is the simple stuff too. Troubleshooting your ABS system? You get nothing other than an ABS light. Could it be a tear in wiring to an ABS sensor? If you are crafty, you can solder that up cleanly yourself for pennies. Could it be air in the brake lines that got into the ABS module? Bleed the air for the cost of a half liter of brake fluid ($10). If a wheel speed sensor shat the bed, that's a $75 repair. If the ABS module shat the bed, well that's much more expensive. Going to the dealer to find out what the ABS light is all about? You will get slapped with a $90 (1 hr labor) diagnostic fee. As a car enthusiast and an engineer, I don't like paying $90 for 5 minutes of diagnostics. What if you go to your local repair shop for the same problem? If they can't read the ABS code, they will have to spend time going down the list of possible things that could go wrong. E.g. all 4 wheel sensors and wiring would have to be inspected (hope the tear is not obvious or not a failed wire inside a connector, where it's not visible!), brakes bled just in case, parts possibly replaced unnecessarily (on a hunch for a common problem). The pure waste in labor that an independent shop has to do wastes the shop's time and your money.
I agree with this. Many of the tasks affected by the law are easy ones -- if you can figure out that they need to be done.
The most common engine repair is replacing a bad O2 sensor -- accounting for over 9% of all engine repairs. That's an easy fix, but increasingly these days requires a specialized tool for no purpose other than making the job hard for a DIY'er. Also accounting for over 9% of engine repairs is a bad seal on fuel filler caps, which cause the "check engine" light to go on. Fixing that is surely a DIY project, if you can read the fault code from the car's computer.
Post may contain irony: discontinue use if experiencing mood swings, nausea or elevated blood pressure.
Heh, that's cute. My Subaru requires removal of an air box, the battery, and a bunch of other stuff before the coil-on-plug unit may be accessed. And yes, the stuff has to come out, because it is otherwise obstructed. Total time to replace a coil unit is about 2 hours if you know what you're doing. Double that if my wife helps.
Auto manufacturers would love to put the independents out of business. Even better if they can legislate them away. "All your repair bucks are belong to us!"
Just put electrical tape over the light.
No brain, no pain.
As a mechanic (some time...) that specializes in electrical / electronic / computer issues, here are some thoughts:
The meaning of "non discrimnatory price", as used in the ballot question will be tied up in lawsuits for years. I can tell you that most of the independent shops out there *CAN NOT* afford to buy Factory Diagnostic Software or Hardware, as a business matter, for more than one or two oem's. Now, granted a lot of this stuff is available via piracy...
Now, if a shop does a lot of one particular make, then yes, it will invest in the "official" factory diagnostic equipment.
Just to give you an idea:
Early 1990's to current Ford Motor Company brand vehicles: Ford IDS (software) / (VCM) hardware combo. price aprox $3,000.
Circa 1980 to early 1990's Ford brand vehicles: Ford / Hickok "NGS" (price aprox $700 on ebay) (antiquated, but highest PID update rate on these vehicles)
And, it's even worse for the independent heavy truck repair shops out there:
(purchase cost + subscription, does not count the specialized interface hardware)
Caterpillar ET software: $1,200.
Cummins Insite software: $1,200.
Detroit Diesel software: $1,800.
Thats the most expensive, but there are a lot of other systems on heavy trucks are computerized too, and take additional expensive propritary software packages to diagnose and service.
For anyone out there who thinks the most expensive diagnostic equipment from Snap-On or OTC is equal to factory, You're wrong. Even the most expensive aftermarket diagnostic equipment out there, has functionality gaps compared to the OEM stuff.
FYI: Now your "average" shop around the corner is usually running a mid range scanner (~$3,000.) taht can do most of the things a mechanic actually needs day in day out. But when you get some whiz-bang software / electrical / electromechanical issue, you get the wrong diagnosis and ineffective / expensive repair. If you have a good honest mechanic, He'll tell you he's limited and suggest a dealership performed service. It's not ideal, but it's having integrity.
Now as a computer / software hobbyist:
Even If I want to code up my own GPL'd diagnostic software, I am limited as to the diagnostic and special test functions that I can implement.
Standard OBDII functions, no problem, It's a semi open standard promulgated by SAE. J1939 standard functionality for heavy trucks, no problem again, another semi open standard promulgated by SAE.
Now lets say i want to implement a standard cylinder contribution test (standard diagnostic test you run all the time). Much more difficult. In today's world You have to license (directly or indirectly) the proprietary protocol info from each manufacturer (under very restrictive terms) you want to implement code for. So that pretty much, kills that.
If you were really hard core about implementing open diagnostic software that could do all (are some sub-set of) the propritary functions for a particular vehicle / engine manufacturer, then you're looking at some serious embedded hw/sw reverse engineering. And,in many cases prior to the mid 1990's, you have multiple proprietary protocols within a given manufacturer / model / year / controller range. That said, there was code and protocol reuse, but... That's why the "open" diagnostic software out there today just doesn't do the specialized stuff. Yet, anyway...
Egads. You say 'big business doesn't give a rat's ass about emissions', then you say all they care about is what they are legally required to do. Well, guess what? Vehicle manufacturers are legally required to care about emissions! They have to make sure that their vehicles are compliant when they are built, and they are required by federal law to provide warrantee service on emissions devices. So yes, they do very much care about emissions, and they certainly care very much about some putz 'tweaking' the ECU and causing the failure of an emission control device which they are then on the hook to fix.
Small engines (lawnmowers, chainsaws, etc) do not have these legal emissions requirements, so any comparison to them is completely invalid.
We have a winner!!!
General Relativity: Space-time tells matter where to go; Matter tells space-time what shape to be.
I'm an old-car junkie. I have none right now, but I have in the past. I spent 3 years as a mechanic for the USAF, and I've wrenched on every car I've had to some extent or another. My last car was OBD I, it blinked, like Capt Pike, to tell you things.
Now I have an OBD II car. The amount of data it captures is remarkable. One would need a sizable battery of old-school analytical tools to match what OBD II gives you for free. You just need to pay a little for the scanner.
For today's car, you need an OBD II reader with freeze-frame capability. Less than 100 bucks. Or, you can get a wi-fi OBD II dongle, and use one of the multitude of scanners and realtime dataloggers for a variety of platforms, iOS and PC included.
Hearing all the whining about how modern cars are not for the shadetree mechanic makes me wince. All it tells me is that people are unwilling to adapt, change and learn new tricks.
I've used a 90 dollar OBD II scanner, a forum and the car's Factory Service Manual to diagnose and conclusively repair the two Check Engine Lights I've had. I tracked both down to dirty solenoid connectors. Why were they dirty and grimy? Long story, but the source of this trouble has been vigorously flogged, and they've lost my business forever.
The language in TFA is weird. What exactly is this info that makers are allegedly holding back? If by "holding back" they mean spend the $120 on the factory service manual, then don't be such a cheapskate and pony up the dosh. I have the FSM for my car. The real FSM, not some Haynes or Chilton wannabe. Every single code my car uses is in there, and I can read them all with a 90 dollar OBD II scanner with freeze-frame. For some of the more exotic things you need a datalogger that records OBD II data realtime. Like I said above, lots to choose from for multiple platforms.
The info is available, you just have to pay for it. Is that so much of a burden?
Mechanics of old had to keep a battery of test equipment (ignition testers, tach/dwell meters, exhaust analyzers, etc) and had to keep up-to-date reference material, all of which cost money. Why should today's mechanics be any different? What, you want the car's codes for free? Na. You need to shell out the $$$ to get the factory service manual. You've always had to.
The "Civilized World" jumped the shark ca. 1973.
"To prevent you from having a "right to repair" the auto manufacturers must simply stop manufacturing automobiles in the USA. Then they can be imported by a licensed distributor and licensed to you to operate. That way you never own your vehicle, and you have no right to tamper (read: repair) with it."
Not a profitable business model. Won't happen. Even dumbfuck car owners who can't turn a lug wrench would come unglued.
"This post is an artistic work of fiction and falsehood. Only a fool would take anything posted here as fact."
"If manufacturers must limit themselves to open, standardized interfaces they will be slower in achieving greater emissions and fuel efficiency."
As an experienced mechanic, I consider that statement imbecilic. You haven't the slightest idea what you are talking about. Please kill yourself and quit wasting oxygen if you care about the planet (and the gene pool).
There are ALREADY some standard diagnostic interfaces, which facilitate diagnosis with common auto store "code readers". Open the rest, particularly those used to troubleshoot NON-ENGINE onboard systems, and the consumer benefits from the removal of VENDOR LOCK.
"This post is an artistic work of fiction and falsehood. Only a fool would take anything posted here as fact."
Just what we need on /. - a computer analogy to explain cars.
Prove anything by multiplying Huge Number times Tiny Number
Apple should be paying close attention to this. One day, people will demand "right to repair" for thier iDevice and Apple will be sitting where the car manufacturers are today...
Just like any car lover I'm always worried what will happen when manufacturers start encrypting the electronic/software then I realize where there's money to be made there will be aftermarket parts like say MegaSquirt. Give it enough time and there will be plug and play systems with custom firmware for any car out there. The hardest part then will be rewiring the damn thing if the wire loom is a mess.
by TheSpoom (715771) Uncaring Linux user here. I have nothing to add to this but please continue. *munches popcorn*
no need to be an ass about it
I did say "total time," which includes getting out the tools and cleaning up afterwards. I'm not running a professional auto shop where tools and equipment are at-the-ready all the time.
Don't know where you got the "just making it harder" bit. Cars nowadays are substantially more complicated than those from as little as 10 years ago. Wrenching on a mid-70s ruster is dirt simple compared to today's machines. And the auto manufacturers didn't make them so just because they could. However, the auto manufacturers do view third-party service shops as "the competition."
Only because it's nearly impossible to tell a Poe apart from someone who actually uses the term "lefties".
--Jeremy
Jesus was a liberal
Just mandate that anything (be it service manuals, tools, computer kit, parts, service bulletins, computer system firmware updates, diagnostic code books, computer system readers or anything else) that the manufacturer makes available to a dealer must be available to anyone else who wants to acquire it. Require that the prices charged for this stuff to dealers is not allowed to be lower than that charged to others.
If there is nothing that only the dealers have then anyone can fix the problems and there is never a reason to go back to the dealers except for recalls (which are done for free) and maybe warranty work.
Admit it. You have no sense of humor and you're a moron because only a moron could miss the sarcasm in that.
Maybe it's because you're 14...mentally at least. Could be physically too I suppose.
When Fascism comes to America, it will call itself Anti-Fascism, and tell you to give up your guns.
Please ignore my post above and mod it to oblivion.
After researching the claims in Kaufman's email, I'm now more confused than ever. I had assumed Kaufman would be on the side of the consumer, as he has in the past. Instead, unless I am reading it wrong, he is on the side of the auto dealers!
The already-agreed new law has a deadline of 2018 and seems to have a loophole that would allow the auto makers to weasel out of providing any meaningful information by not requiring it to be revealing if it involves a "trade secret".
Voting "Yes", which would override the new law, would set the deadline to 2015 and would not have this loophole, as far as I can tell.
Don't take me at my word but research it yourself. I am disappointed in Kaufman's misleading email and wonder if he is in cahoots with the auto dealer lobby.
Your car will FAIL INSPECTION with a fault light
You CANNOT legally drive your car without inspection
You DO NOT have to get your computer inspected, you can CONTINUE to use it with the lit fault light.
What happens when the automaker goes out of business?
YES it happens! SAAB!
Do they take their encrypted codes with them into oblivion?
There are NO MORE Saab dealerships. You MUST get your Saab repaired by an independent garage!
WHERE do they get the codes?
they certainly care very much about some putz 'tweaking' the ECU and causing the failure of an emission control device which they are then on the hook to fix.
EGADS!
You mean if "some putz tweaks the ECU" that THE MANUFACTURER is "on the hook to fix?"
WOW I NEED TO GET OUT THERE AND TWEAK ON MY CAR SO SOMEONE ELSE IS ON THE HOOK TO FIX IT.
> the Supreme Court just held up that "first sale" doesn't count if the *thing* was intended to be sold to a segregated market, or sold to you by an unlicensed distributor. No, they heard the arguments for a case that, if it goes anti-first-sale, would mean that a sale in a foreign country does not constitute "first-sale". So this would just mean if you bought your car in China and then try to have it shipped to the US, you would not have resale rights
I would much rather work on a modern car than a classic. In fact, my hobby is retrofitting modern components into classic cars, including ECUs. The concepts on this ballot are important because the manufacturers would like to completely lock us out of the ECU, THAT would be an issue. As is, as long as they ECU can be talked to, and we can have basic access to it, it's not particularly difficult to work on a modern car (and they self-diagnose far better than classics).
If you really need to control an engine and don't have access to the original ECU for some reason, replacing it with an aftermarket ECU is not difficult, it just requires (very basic) coding knowledge. The basic guts of an ICE haven't changed much, and even variable valve timing and direct injection are not particularly complex concepts to tune. The fact that the skill set to work on modern engines is different than classic engines doesn't mean that they are worse or harder to work on, it just means you need different skills. This is like people saying that computers suck to work on now that they aren't full of tubes, that's only true if you only know how to work on tubes.
Just another ignorant American.
It's for their mother-in-law's car, I think it's a 70s Pinto.
If manufacturers must limit themselves to open, standardized interfaces they will be slower in achieving greater emissions and fuel efficiency.
This doesn't make any sense.
Go into any University research department in the World, and you'll see all the experimentation and all the learning taking place on open hardware and/or on open source software. The same goes for hobbyists and tinkerers. Those people were usually the first ones to experiment with alternative fuel technologies and converting existing cars/trucks.
Close everything up, let everything become embedded and proprietary, and you may kill off our next generation of car inventors and engineers.