Slashdot Mirror
Serial ATA 1.0 Draft Released
Several readers submitted the news from CNET's story regarding the Serial ATA 1.0 Draft Released. Looks like the replacement for IDE is getting closer - a peak transfer rate of 150 MBs per second is nice to have under the hood.
Nothing is wrong with SCSI. Actually, SCSI will always be superior to this standard. I guess, however, if you wanted to say that there is something wrong with SCSI, its that it is far too expensive for most people. The reason for this is that SCSI is a much more intelligent device and thus requires much more sophisticated electronics. That is one reason why IDE is so popular, is because it is far cheaper. But with this reduced cost, you are limited to the number of devices you can put on an IDE chain. IDE=2 per chain, SCSI=8 (including controller) per chain. There are some other technical details (disconnect, for example) which make SCSI better, but again.. price.
--
Never hit your grandmother with a shovel, for it leaves a bad impression on her mind...
Yes - and it is sooo difficult to simply cut your Ribbon cables w/ an Utility knife, twist one end around once or twice, zip it all up with a cable tye or two - and Voila! you have a 'non-air impeding' cable from MoBo to HD. I dont know anyone who clocked their box who hasnt done this... simple and effective. Have a look at the /. article here
RTFA -- or maybe C|Net skipped the important details, adn I'm just working off of what I know.
There is a steady phasing out of the 5V line in PC power supplies in favor of 12V only. More bandwidth -- it is widely believed that ATA/100 was the very last drop that could be squeezed out of parallel ATA -- improved cooling and cabling options, because the 6 or 8 wire cable with be sinificantly less obstructive to airflow, and becuase the cable can be twice as long and more flexible, it can be routed out of the way more easily.
You might be happy with your SCSI setup, but your wallet probably isn't. I went with an all SCSI rig a couple of years ago -- it performed *better*, but not enough to excuse the price. Wait until you see the $/GB divide of SCSI and IDE grow even wider. Wait until they stop making hard drives for your specific protocol and you're stuck with drives that once were big but are no longer as large as today's entry level drives...
Shit, I'm late for work.
"Watch these suckers jump when I get root." - l33t j03
Serial ATA is just another serial connection like USB and FireWire. They're trying to make us use serial ATA hard drives which will slow down when we connect another one to the chain. Support will be decent, fortunately (which isn't the case with USB and FireWire; Intel shuns 1394 in favor of USB2, and USB still has yet to see some non-WinHardware). I don't care if I have to convert all my stuff to Ultra SCSI, I'm just not going to accept this proletarianizing of hardware.
"Ancillary does not mean you get to rule the world." --U.S. Circuit Judge Harry Edwards, speaking to the FCC's lawyer
Forget Scsi! The idea is smaller cabes that are less prone to block airflow! Cooling is where it's at. Anyone who's built a computer will see why this makes sense I tell ya
"Give a man a fire and he's warm for a day, but set fire to him and he's warm for the rest of his life." Terry Pratchet
PCI HD controller
I feel sure the manufacturers of the drives will make whatever they think ppl will buy. They don't care so much about other ppls content as long as their drives sell.
We will see non-compliant drives even if this standard is widely accepted (which it won't be) just like dvd makers now seem to "forget" to strictly apply region code checks.
-- MartinG To mail me: echo kewyjlcxyzvjfxbqwh | tr bcefhjklqvwxyz
Would someone explain to me how serial is faster than parallel? I mean parallel is just that, sending multiple bits in parallel, serial is sending single bits in series. I would think that sending less information in series would be much slower than sending more in parallel.
What am I missing?
-josh
Remember floppies? The 1440 KB variety replaced 720 KB only because they were similarly priced, backward compatible at the hardware level, and doubled capacity. Then 2880 failed to gain acceptance because it failed to deliver the same advantages.
Same thing with the two-sided CD format. The added cost of the hardware will ensure that it is never widely adopted. Unless you can flip the thing over and treat it like a second disk in older drives. Maybe then it will fly.
As a demonstration technology, it will perhaps be interesting, but until the cost is about the same as PATA, and it gets closer to really being "double the bandwidth", I don't look for any better market penetration than, say, ESDI drives with MCA host adapters.
[100% ISO 646 Compliant]
SVM, ERGO MONSTRO.
Just think, using this to network a couple computers together.
Serial ATA Networking...SATAN.
'course, if they are naming this the way they name current ATA specs... then we might just get 100 MB/s out of it.
--
> In addition, Serial ATA will let each drive communicate directly with the processor. Currently, the different drives must share a common connection.
Finally, a good reason not to have to pay out the wazoo for SCSI, while hopefully doing away with IDE interrupts.
http://www.mp3.com/subatomicacorn
"Old man yells at systemd"
That's almost useless.
I have 4 IDE ports on the mobo and a PCI controller with another 4 ports. However due to the length limitations of the IDE cables I cannot use all of them. And I have plenty of space in my full tower case.
Simple, it's to keep up with those 1.4 GHz processors, which are effectively twice as fast as 1 GHz processors.
+5:offtopic,but anti-American
Just out of curiousity...what's to prevent using an encrypted filesystem on one of these (yet-to-be-created) drives?
I mean, if all the drive ever sees is a stream of 3DES bits, how's it supposed to know that there's anything contraband going on to it?
Or would this make encryption an illegal DCMA-circumvention device?
I don't think we need to worry, just yet.
b&
All but God can prove this sentence true.
Which doesn't make much sense, since the whole m.o. of slashdot is that almost every "story" is "stolen" from another source. /. is a news clearinghouse, not a news provider.
"That basically equates to about 150MB of data per second," Ravencraft said. In comparison, Parallel ATA's ATA 100 offers a peak transfer rate of 100MB per second."
Yeah CNET, glad to see that in the new math system, double 100mbps is 150, not 200. And to think, my whole life I've been lied to. Maybe thats why my boss laughed at me when I asked him for double my pay from 10/hour to 15/hour...
Go figure...
-C
"Well kids, you tried your best, and you failed. The lesson is, never try." -Homer Simpson
SCSI can go up to 320MB/s but that's shared among all of the drives on the chain. SerialATA gets rid of the whole chain idea, it's a point to point connection, so while it's only a 150MB/s link, it's not shared between drives.
You also need to ask, what is the peak transfer speed of the fastest HDD around, right now it's around 60MB/s if I remember correctly, not even enough to max out ATA66, the only time you need ATA100 is if you're using the slave channel. So while 150MB/s seems slow compared to the fastest SCSI connection around, you never have to share it with another device.
-Ted
there is no law _requiring_ copyright control on harddrives, or anywhere
Currently. Willing to bet we are not going to see one in our lifetimes? After DMCA everything is possible.
And it's not like the government has objections to outlawing hardware: e.g. scanners able to listen to cellphone frequencies.
Kaa
Kaa
Kaa's Law: In any sufficiently large group of people most are idiots.
Man thanks for telling me that. I'll turn off my Blue G3(rev 1 even) right now and disconnect my Maxtor 13 gig slave. I'll also have to take the 60 gig maxtor slave drive out of my G4. What a bummer.
The only reason IDE is popular is because it is cheap. When you go all the way back to PIO transfers the IDE interface is among the simplest. DMA doesn't make it that much more complicated.
Data transfer rates aside (the physical transfer
rates from the media can't keep up, so why the push for faster bus rates?), SCSI still out performs IDE. Give me tagged command queing and Serial ATA MIGHT be competetive, but then the drives won't have the price point, and SCSI has the faster transfer rates, etc.
Also one thing to note, IDE drives and SCSI drives seem to be using different storage technologies even when you don't consider the transfer mediums.
In standard half height 3.5" drives SCSI is availible in up to 36 GB (Like my IBM UltraStar 10k rpm drive), but IDE is availible in up to 80 GM (Like the Maxtor I put in my TiVo). The SCSI drive is 10k rpm, the IDE is 5.4k rpm. The SCSI drive was twice the price.
The controllers aren't the problem with SCSI, my ultra160 dual channel controller was $179, not really bad. The premium on the drive price is another story though.
why bother with a new interface that isn't as good as firewire, when firewire is already here, and runs at 400mbs instead of a measley 150mbs??
Here's to hoping Firewire wins out this one.
There are already Firewire drives of comparable price to EIDE and of comparable size.
Firewire cards, devices, and OS support already exists.
Firewire is already working over version 2, with plans for version 3, as well as wireless!
Geek dating!
GPL Deconstructed
It was called Firewire. Apple already makes provisions for in in all their current PCs. You can also buy them at prices and sizes comparable to current IDE drives, so the aren't nearly as expensive or high end as serial ATA. The SATA essentially provides for EIDE what SCSI has had for ages, and what Firewire was built with as well; command queueing, daisy chaining multiple devices, and processor decoupling for the data chain. It's just a simpler design, with less wires. Me, I hope Firewire wins this one.
Geek dating!
GPL Deconstructed
I've always wondered why the hdparm manpage says: Using DMA does not necessarily provide any improvement in throughput or system performance, but many folks swear by it. Your mileage may vary.
;-)
It seems to help a lot on my systems.
The same manpage mentions: It is also a good idea to use the -X34 option in combination with -d1.
This never fails to crash my systems
I've already made two reply posts to others in the thread.
Firewire! Go Firewire!
They are at spec1 in hard disks, notebooks, PCs, cameras, camcorders, and PS2s. Spec2 is already on the way, with designs for spec3, as well as wireless.
It is comparably priced to EIDE at similar sizes, and already has every single benefit that is being touted for SATA, but now and cheaper ^^
SCSI is SCSI, and won't be going away any time soon. But here's to hoping Firewire wins!
Geek dating!
GPL Deconstructed
it has some interesting features, though a monster transfer rate isn't one of them - no addressing, point-to-point connection, etc.
so, with serial ide, if each device can communicate with the cpu directly is there going to be a limit, like scsi and parallel ide, of one data transfer operation at a time per bus? or will it really be serial (like SSA) and allow multiple simultaneous data transfers?
Bus speeds are up, interface speeds are up, memory bandwidth is up, and we're still suffering under meager disk I/O data rates. MAKE DISKS FASTER! Instead of a 40 GB, 3 platter/6 head model, I'll pay the same for a 4 GB, 10 platter,20 head model. Instead of a "stack of records" style, arrange the heads like in a roll of coins. Yes, its more $$ for head design and driver hardware. I want 100MB/sec from the media!
I want to delete my account but Slashdot doesn't allow it.
I tend to agree with those saying the market will mean non-compliant drives will remain available one way or another.
For example, I live in Australia. Here, DVD players are supposed to only allow the playing of Zone 2 DVD's (or whatever our zone is). That's so movies can be released earlier in Zome 1 (the US) and not playable by the rest of us.
1st generation ones were zone restricted according to the standards. Some still are. But, the fact is, the majority of DVD players on the market here now, I believe, have that function disabled before they leave the factory and will play any zone DVD's. The consumer won that one here.
Sure, this doesn't PROVE much because it's a slightly different situation, but it seems to be indicative of what often happens.
Darren
I just posted another point somewhere in the threads here (have fun looking) but according to another story I found, the Serial ATA Standard will scale to 600MB/s. SCSI Wasn't always 320MB/s, and IDE wasn't always 100 MB/s. You have to keep in mind this is the first bit of the technology.
Anyone know what Fibre Channel/IEEE 1394 current hard drive standards run at?
There is (or was) support for serial SCSI in the specs (the target at the time was high-speed serial links such as fiber, but it would apply to links similar to serial-ata as well). Also SCSI allows for target-mode, which would allow this serial bus to be used as a very-high-speed very-local-network.
Why would there be nothing else in the shops?
How do you thing shops decide what to stock?
How do you think manufacturers know what to make?
Answer: Whatever the customers want to buy because that's the only way they can make money.
-- MartinG To mail me: echo kewyjlcxyzvjfxbqwh | tr bcefhjklqvwxyz
They didn't say that serial ata would be more expensive that scsi, they just suggested that it would be more expensive than ata100. But you're right in a way - how will they get it implemented on high end workstations when SCSI is so much better? Who will they aim the inital tech uptake at? It certainly won't get cheap enough if no-one takes it up. But it's looking like no-one will have a good enough reason to take it up if it can't compete with scsi and raid. What's the deal with serial anyway? I thought parallel was better just on principle?
lemonade was a popular drink and it still is
YOU might not want to buy one, but the Great Unwashed will demand nothing else since non-conforming drives won't support the applications that want to use it - RealPlayer10, WMP-2002 etc.
With the major manufacturers shipping these drives in preconfigured PCs, support will soon be strong enough to permit the applications to be fussy.
But it will take 2 years to get the drives into the market (not just for sale, but in a fair proportion of users machines). It will then take another year before a new download format has some credibility. Three years of keen cracking is a very long while. The protection has to be strong or they'll have to start all over again with CRAP^H^HMP-2
Maybe I am picky but what is FireWire's fastest speed? 400 Mbps/50 MBps? The current FibreChannel spec supports much more. The last FibreChannel controller I worked on did around 200 MBps on one loop. FibreChannel can use a hub/switch topology. FC may be a bit storage centric but no more than SCSI is. The only thing I find compelling about FireWire is its price. That is why my main point was that companies should work on making the best technologies less expensive rather than cheaper but lower performing alternatives. In my opinion FireWire and USB are just watered down options. They are cheap but slow. IDE, Serial ports, classic ports, etc. are even cheaper but even slower. How does FireWire not fit into this?
InfiniBand is looking out to be a great replacment for PCI. It gives you the ability to pull the bus out of the box and also uses a hub/switch network like topology. It supports various speeds and a memory model that lends itself to clustering. While InfiniBand is pretty new, the industry is backing it. Intel already has a Target Controllers ready. Host controllers are coming soon.
Combined they give you a lot of flexibility. The Infiniband network for all data traffic and the FibreChannel network for all storage traffic.
-- soldack
BZZZZT! Wrong!
Not when there is a monopoly, it aint. Then they ram whatever they want down your throat. And we are talking about some BIG monopolies here, for starters, Micros~1 and the RIAA and the MPAA etc.
Look into the 'secure content stream' or whatever is is called in windows (there is a technote somewhere on msdn)
This could easily be coupled to such a hardware scheme, requiring only 'secured' content to be stored on these devices. Windows may only boot from such a hard-drive, movies may only play on a computer with one etc etc etc.
WAKE THE FUCK UP!!!
Where is a very convincing argument why not use Firewire. It sounds like "$1 per firewire port".
Why should there be nothing else? Re. to my question, why should the consumer (or OEM for that matter) purchase drives with such a 'feature' that may even hinder legitimate backups? No discernible benefit. Besides, consumers have a *right* in most countries to back up software they have legitimately purchased.
I work for .. errm .. a lickable, fruit-like computer company & have some responsibility for download of customer software bundles to new Ma^H^H computers. I can see a firmware-based mechanism like this causing plenty of technical headaches for systems manufacturers and VARs. So why bother?
Alison
"It is a miracle that curiosity survives formal education." - Albert Einstein
If I have these right:
USB maxes out at 1.5 meg a second.
Firewire tops out at 40 meg a second.
SerialATA goes to 150 meg a second.
Parallel ATA (IDE) does 16.7, 33, 66 or 100 meg a second.
SCSI runs 5, 10, 20, 40, 80 and 160 meg a second.
Supposedly serial ATA will transparently work with OSs that support parallel ATA. So you can run MS-DOS 5 and Win3.1 on your new 4.3 GHz P5.
Abit have had one that supports 8 devices for ages
Die? Thats the last thing I intend to do!
What's wrong with SCSI?
Price.
Can this do something that SCSI cannot?
Yes, provide (much) more bang for the buck.
Kaa
Kaa
Kaa's Law: In any sufficiently large group of people most are idiots.
Both in PC software and in video formats.
And it was an abject failure.
The people who wanted to quickly found ways to circumvent the idiot copy protection (hmmm, wait, under DMCA, that's illegal) and the cud-chewing herd just lost their data when the media died.
These greedy f*ckers don't want to accept that inevitably, information (state secrets, corporate skulldugery, music, movies, software, games) will be free. It's an erosive force, just like water. In the internet age, once one person knows how to break a lock, everyone can know it.
If something like this somehow makes it to market, all these companies are going to do is make life hell for their less sophisticated customers. Anyone with enough brains to bang two rocks together will circumvent this a week after it hits the streets.
What really is starting to worry me about the issues swirling around the DMCA, MPAA/RIAA, DeCess, et al is that these corporate interests are attempting to bend our legal system to their ends. In order to line their own pockets, they promote idiot laws, that anyone who's a non-idiot blatently disregards. Just like our ill-advised drug policy, this is another case where we are training a generation to ignore the law, because it is craven and stupid. In pushing such measures, the media industry is further hastening the decay of the rule of law in the American republic.
Historians will look back to this as a golden age rife with opportunities, and wonder why we allowed things to get so f*cked up.
Annonymous Coward -- "First they came for fair use, and I didn't speak up because I wasn't a pirate..."
The reason SCSI is so much more expensive than IDE is simply a question of target market.
IDE is targeted to JethroBoBillyBubbaSixPack who is running HoggingDOS98. He is limited by his crappy OS, and a drive that can disconnect from the bus and call back later when it is done with the operation is not going to do him a damn bit of good. He wants big and cheap. Real speed isn't important to him (although he is impressed by high RPM numbers).
SCSI is targeted at folks building servers, high-end workstations, video editing stations, etc. In other words, people who are spending other people's money (for the most part). They know that being able to do a disconnect and free the bus for something else, being able to to scatter/gather and elevator optimatizations, being able to buffer disk I/O properly, and being able to hang many drives off 1 card are more important.
As a result, SCSI is more expensive because people will pay more.
www.eFax.com are spammers
From Cnet's article:
...and lower down in the same article...
The Serial ATA Working Group published the 1.0 draft of its specification, which will effectively double the bandwidth, or capacity for data, between disk drives
"That basically equates to about 150MB of data per second," Ravencraft said. In comparison, Parallel ATA's ATA 100 offers a peak transfer rate of 100MB per second.
When did 150 become (2*100) ?
nuclear presidential echelon assassination encryption virulent strain
Whizzmo
When was the last time you bought a MPAA hard drive?
Read the story. This abomination is pushed by IBM, Toshiba, Matsushita, and Intel. They (maybe not Intel, but it makes the chips) actually do make drives.
Besides, the way to market it will be: "Our new drives do all old drives could, *plus* they allow you to buy songs/videos/etc. off the Internet!"
Kaa
Kaa
Kaa's Law: In any sufficiently large group of people most are idiots.
It exists. It's called "SSA" (Serial Storage Architecture) and it's by IBM and it's quite neat. It is used quite extensively in RS/6000 systems and is an "open" standard. Unfortunately, about a year ago when I stopped working with RS/6000 machines, it seemed that SSA was suffering from Not Invented Here syndrome and the industry was moving to F-CAL. Oh well.
Cheers, Robert.
There is a place for IDE, and a place for SCSI. For Captain Jow-Blow-Win98 at home on his desktop PC, there really is no need for SCSI. IDE is cheap enough for him not to bitch, and it runs just fine.
I work at a company that is doing unified messaging... We need massive amounts of storage here. If I look out the door of my office, I see some disk arrays that hold a total of about 5 Terabytes of space. You think were going to be running IDE on this? OF COURSE NOT. SCSI is, and probably will always be, 100 times more robust than IDE will ever be. Hot-Swap, 15 devices on one interface as opposed to 2, reliability, RAID 5.
I mean, who needs that in their own home PC? Not Captain Jow-Blow-Win98 user.. Or even Joe-Blow-Linux user for that matter.
-Rob
1. Serial protocol more noise resistant, longer cables at higher freq without signal problems or FCC issues.
2. Compatible protocol. Should be fairly simple to create drives/chipsets that support both serial and parallel ATA. Host or drive side dongles will also readily available.
3. Chipsets are getting so integrated that they just can't fit all those pins on them any more. This is becoming problem for creating Tinma style systems.
see the diff?
||| I still can't believe Parkay's not butter.
Serial ATA is old news. BTW, if you were wondering, it looks like Linux will have support for Serial ATA. Andre Hedrick, one of the "senior" kernel developers, is a member of the Serial ATA working group.
Torrey Hoffman (Azog)
Torrey Hoffman (Azog)
"HTML needs a rant tag" - Alan Cox
That's a fake CmndrTaco generated first post if I ever saw one!
Keeping
Linux will be one of the first OS's to have this protocol support..
Hetz (Heunique)
It's CmdrTaco and not CmndrTaco.
Before you email me, remember: "There is no god!"
Not quite. USB1 is 1.5MBps and Firewire (1394a) is 50MBps. Newly arrived USB2 can do 60MBps, and IEEE-1394b starts at 100MBps and will go up to 400MBps in a couple years.
And of course, 1394 supports up to 63 devices per bus, hot-swappable, networkable, yadda yadda yadda. But my favorite Firewire trick (target disk mode) is Mac only. Let's see IDE match that.
And it takes only about 3-4 wires to use it, rather than the 50-odd wires you find in SCSI and IDE cables. THAT is a pretty big deal; that simplifies the building and layout of systems.
The really cool part would be to stick a whole lot of Serial-ATA interfaces onto a system; while it would be ludicrous to try to connect 6 SCSI cards to a PCI bus, as the attendant cabling for the potential 90 SCSI drives would be be frightening, and result in a system shaped like the star required to get those cables to go in 6 different directions, the simpler cabling of Serial-ATA might allow such a design to be much cleaner. :-).
It's certainly not as nice as the latest and fanciest SCSI standard, but if it makes plugging in an extra few drives a cheap and simple matter, that will suffice. SCSI is neither simple nor cheap.
(Note: The only SCSI variation that I don't have drives for, at this point, is the latest 80MB thing that just doubled "Ultra-Wide" bandwidth again.)
If you're not part of the solution, you're part of the precipitate.
What the hell do I care? Y'know how expensive this will be? For the home user it'll be quite some time before they'll be able to take advantage of this new spec.
Besides, SCSI is still better...
Peak is 150? and what about average? 60? 80? Cost of changing hardware? how it will act in RAID? and what for ATA 100 if we already got SCSI? (UW etc...)
IEEE-1394b (note the 'b') may well be finalized at their meeting next month. The speeds it will offer are 800mbps, 1600mbps, with extensions to reach 3200mbps, giving you:
:^)
100Meg a second, 200Meg a second, and 400Meg a second. Take *that*, Ultra320 SCSI!
Also note that unlike ATA, SCSI, and SerialATA, FireWire doesn't require a computer - you can hook devices up directly to each other (digital camera to firewire hd, etc.)
And for the overclockers/modders - skinny cables with FireWire, too.
And note to the person who mentioned Apple's FireWire ports on the Mac motherboards - seems Apple has discontinued the internal firewire ports on the latest Macs, from what I hear. Still have the external one(s), though.
Exclusive
Hastening a rapid demise for the free copying of digital media, the next generation of hard disks is likely to come with copyright protection countermeasures built in.
Technical committees of NCTIS, the ANSI-blessed standards body, have been discussing the incorporation of content protection currently used for removable media into industry-standard ATA drives, using proprietary technology originating from the 4C Entity. They're the people who brought you CSS2: IBM, Toshiba Intel and Matsushita.
Why is a replacement for IDE being designed now? What's wrong with SCSI? Can this do something that SCSI cannot? I recently changed over to SCSI and I couldn't be happier.
-- MartinG To mail me: echo kewyjlcxyzvjfxbqwh | tr bcefhjklqvwxyz
1)What are the current peak transfer rates for IDE and SCSI?
;o) )
2)What sort of transfer rate do other technologies like IBM solid state drive, Flash etc have?
(answers these and I can post inteligently (ish)
While the website points out that SerialATA is an internal, in-box protocol and that USB-2 and 1394 (Firewire) are primarily for connection of external devices, they never really address the point that both of these other protocols are also available for use in-box. Apple, for example, has provided 1394 connectors on the MLB to allow F/W drives to be installed. Also, both of these protocols are (largely) already established in the marketplace. So what's the big deal ... ??
Alison
"It is a miracle that curiosity survives formal education." - Albert Einstein
Why not make an internal serial SCSI spec with smaller cables?
- Michael T. Babcock (Yes, I blog)
hardware geeks and case modders rejoice, as serial ata uses a skinny litle cable, much like the audio out cable from your cd-rom to your sound card. makes the case a lot neater (imagine hiding the cables by taping them to the sides of the case!) and increases airflow. check out yummy pictures at http://www.anandtech.com/showdoc.html?i=1174.
complex
I have downloaded the spec. (it can be found here)
They change the connectors.
There will be new style data (that was expected) but also power (not expected) connectors. Thus you'll have to change power supply.
It seems though that they made the connectors so that devices will be capable of hot-plug (some connections are longer than other, just like for USB. There is also a standard positioning (so that there will be a standard type of disk drawer, building on the "hot plug" apparent capability)
IDE's 2 per chain blows chunks. Macs, which now use IDE to reduce cost, don't even support slave devices. They are one device per controller. Gaawwwdd that's inefficient!
Have fun!
Psst! Yes, they *really* are out to get you!
i wonder if these SATA kabels could be used as a cheap highspeed network for boxes in a cluster. eventuelly they could not be directly connected via a crossover kable but a small adapter in between that simulates a small harddriver to both (or more ends) could be used for fast internconnection. IPoverSATA anyone?
I upgraded my computer last year and moved from ATA/33 to ATA/66. I guess maybe it's sorta faster. Maybe. Or that could be wishful thinking. I even tried some benchmarks, and they looked good. But on the day-to-day use of my computer, how different is it? Am I really booting much faster? Do my applications really start that much quicker? And if the hard drive can't read data any faster, would it do me any good to have a 500 TB/s transfer rate?
"I am a cipher, a cipher, wrapped in an enigma, smothered in secret sauce" -Jimmy James
The increasing sizes of commodity hard drives, and the increasing use of hard drive space, will drive the demand for higher and higher bandwidth busses. Hard drives are doubling in density roughly every 12 months, and doubling in peak deliverable bandwidth every 24 months (since the density of a track increases sqrt(2) every 12 months, causing the head to cover twice as many sectors per revolution of the platter).
For a good long while now, busses were capable of sustaining much more bandwidth than the drives were capable of delivering, so busses did not have much need to increase in speed. Lately, however, the peak bandwidth of individual drives has been approaching bus capacity, hence the sudden advances in bus technology (ATA/33,
Eventually I think IDE will have to follow in SCSI's footsteps and go to optical fiber. It's the only way to keep up the pace. SATA is (again, IMO) a transient technology, an interim solution between PATA and FATA, much as VLB was an interim solution between ISA and PCI.
As to "why IDE?", the answers are pretty much what people have already said -- price (hardware manufacturers already have uber-integrated one-chip solutions for IDE devices and controllers, and the only difference between SCSI and IDE hardware is the logic), and established technology base (ie, everyone's commodity systems software has standardized on IDE). It's like the x86 instruction set, a legacy that we're more or less stuck with for the foreseeable future.
-- Guges --
I've lost count of the number of UDMA capable machines I've seen running in PIO mode under both Linux and NT. Not only are data-transfer speeds lousy, but CPU utilisation during data-transfer is obscene. Then they wonder why their applications are running slowly.
Clueless MCSEs appear to do this all the time!
... and if you compared a 5400rpm/ata33 drive to a 5400rpm/ata100 drive, you _wouldn't_ "consider that an increase in speed and performance..."
A few examples:
Xeon CPUs cost 10 times as much as their Pentium III counterparts
Any computer case that fits into a 19" rack will have its price tripled
Sun Microsystems servers cost... well, it's rediculous.
An audio CD library jukebox that can hold 200 CDs will cost about $200, but if that jukebox were to hold data CDs, the price is in the thousands.
I/O Error G-17: Aborting Installation
So instead of 1 cable from the motherboard hooking up 1 - 15 drives (scsi) you have lots of cables with lots of connectors on the MB.
If you want your drives external, then you have lots of cables from the computer to the drive chassis! Dumb Dumb Dumb. The foresight of the SATA people is NIL.
2000-12-21 09:12:57 CopyProtection on next generation HardDrives (articles,news) (rejected)
1. IS the limit still 4 devices? 2. Can you raid them? 3. Since its serial, can use it like firewire/usb? 4. What is the actually speed? 200m or 1.5g?
Now all the motherboards need is support for more than 4 ide devices. Has anyone seen some of the nice gigabyte boards that are being produced? Its nice to finally have support for more devices. Now if they made these boards to support the new standards, I would be in heaven.
the scsi standard has been around forever. why are they trying to recreate the wheel. sure scsi is expensive, but this ata 1.0 stuff isn't going to be cheap. if as much money, effort, and time had been spent on getting people to use scsi disks as has been spent on ide crap, then the price for scsi devices would be compairable to that of ide.
use LaTeX? want an online reference manager that
-- john
Microsoft for one, as stated in the article, is seriously opposed to this. So should be any OS or large application vendor, for the reasons described therein. They do have some big clout. :)
;) Without a chipset with these new ATA commands in it, the drives are useless. So here's a weak point.
:) What about downloading stuff off the Net? I'm sure programs will also be used to strip copyright information off a file as well, or some apps will be written to do filecopying by getting around this.
Not all the HD manufacturers are in this little committee, and I'm sure they'll do whatever will make them more money. If this means going against the committee and either persisting with ATA-100 or making their own version, if there is a market for this product, they will do it.
Now this is _very_ important - New standards need new chipsets - the interface for ATA is held on the motherboard. Intel is on this committee, sure, but what about AMD? VIA? Now, they wouldn't want to do something differently from Intel, would they?
I'm sure there'll be workarounds built as quickly as DeCSS was. Cables with de-protection dongles built in? Nice one.
There are more potential problem scenarios for this. If file X is "protected" in this manner, what about X.zip?
(this is a tangent from this - the new ATA standard would be a hardware check on the HD, i know, but from the article i gather it would be effectively on request of the file/application)
In short, I would keep a close eye on it, but I wouldn't worry. If it becomes a reality (as in, a major choice and in stores), tools will be all over Warez sites. Think of the volume of DeCSS out there, now multiply it by the number of Windows users there are - and this would be a hack for something REALLY annoying.
It'll be tried and will fail - there is no law _requiring_ copyright control on harddrives, or anywhere, so the fight will be on, with people boycotting the new drives and sticking with ATA-100 or SCSI-UW, or hacking them. Until the next standard comes along, which won't have this control on it, and will sell like hotcakes.
Get our yer mirror sites.
Fross
Does anyone have any other info on this? This is one time I can actually support M$, at least they can do some things right.
sopwath
I hope that you don't think that SCSI implementations are really as expensive as the manufacturers are charging for them. People/companies will pay more for SCSI than IDE because of the performance difference, whether perceived or not.
Servers generally use SCSI because there is a performance difference. Corporations buy servers. Manufactures will charge what they can get, not what things actually cost.
This is one of those technologies, like SDMI and CSS that do nothing to advantage us, the consumer, but gives all the cards to the big entertainment corporations. One by one our freedoms have been taken away, but now they have reached the stage where they want to control what we do in our own homes, on our own computers. Can you imagine not being able to copy your own files around, even between hard disks in the same computer? This is one of those things that must be faught and faught until it is dead and buried.
Folks,
The reason why Serial ATA is being developed is simple: going to SCSI--especially Ultra2-Wide and Ultra 160--is a VERY expensive option.
Have you seen the cost of Ultra 160 SCSI adapters? Or how much the cabling costs? Or how much Ultra 160-compatible SCSI drives cost? Pretty expensive, and no thanks.
Serial ATA will of course initially cost more than UDMA/100, but it still would be much less expensive to implement than Ultra 160 SCSI. And because Serial ATA does not use those pesky flat ribbon cables, installation is also much less of a hassle, especially now you have much less interference with interior air flow of a system case, which will actually promote longer life of computer components. The best thing is that Serial ATA does not require a drastic change in the operating system to support it out of the box other than getting motherboard chipset drivers for the South Bridge chip that has the Serial ATA support, and given that most motherboard manufacturers include a CD-ROM disk with these drivers as standard....
Raymond in Mountain View, CA
They changed the cable from 40 to 80 pin when they went from 33 to 66
From The Register's story:
.. EVEN LESS! But they were wonderful devices, these floppy disks. We could make as many copies as we wanted as one, and store whatever we wanted! Oh those were the days, when the MP3s flowed free, and the DeCSS rebels weren't laughed at by the public. Yes. Those were the days."
"Where were you when they copy-protected the hardware, Daddy?"
"Well son, way back in the year 2000, we had these wonderful devices called CD Recorders. We could copy almost any CD! Except for evil CDs with defective sectors burn into them, they required a little more work my lad. And we had these great devices called IDE Hard Drives. You could store 80GB of anything you wanted on one of these disks! And copy it to any drive!"
"80GB? You're old dad! How many gigabytes is a terrabyte again? Johnny down the street just got a new Fiber Channel 740TB Drive. Can I get one for the holidays?"
"We'll see, son. I'm liking the looks of the new nanodrives. But anyhow, continuing my story. We had all sorts of magical hardware. We had Orb Disks, which held 2.2 GB! And these things called zip disks, which held 250 or 100MB!"
"100MB?! Ha ha dad. I can't even fit a Word 2044 Document on that!"
"You think 100MB is small? Wayyy back in the day we had things called FLOPPY DISKS. And they only held 1.44MB, 720K, 360K, or
Here's another story I found:
"Intel propses new hard drive standard"
http://internet.idg.net/crd_ata_289383.html
"Upon introduction, the new interface will perform at 1.6Gbps as opposed to the current ATA standard, which is just under 1Gbps, according to an Intel spokesperson. The Serial ATA interface is expected to eventually scale to 6Gbps. First demonstrations of the product are expected this fall."
6 gigabits a second turns into [about] 600MB/s right? Not too shabby.
Remember, SCSI and IDE sucked too when they first came out. The Serial ATA specification is built to scale to keep up with industry designs. So we're not going to be stuck at 150MB/s forever.
Why can't these companies concentrate on making the good technologies out there cheaper? Enough of these watered down attempts like USB and FireWire. Enough with PCI and PCI-X. We know we have things that are better. I am so tired of good hardware costing so much more just because the vendors can get away with charging more. They claim you are paying for performance, development costs, etc. but I think you are paying for a lack of real competition. All these companies that make SCSI drives yet prices in this market didn't fall like the IDE market? Does it really cost that much more to build a scsi drive than an IDE one? What about a fibre channel controller and drives vs. similar SCSI controller and drives? It is unbelievable!
By the by...although InfiniBand is pretty new it has great potential. It makes a great platform for both storage and network traffic. I am currently working on drivers for storage (fc) and network (GB ethernet) devices over InfiniBand. And our first target platform is...Linux!
-- soldack
I think it's really dumb that ./ decided to post the serial ATA story and NOTHING about this, even though many people have submitted the story.