Slashdot Mirror

The updated fifth-generation iPad mini has been torn apart by iFixit, revealing an "amalgamation of components and designs from other iPads -- the internals of a previous iPad mini, the camera system of an iPad Pro, and the exterior design of an iPad Air," reports Ars Technica. From the report: iFixit has published its teardown of the new, fifth-generation iPad mini -- the first update to Apple's smaller-sized tablet since 2015. The iFixit team -- which sells gear for repairing and servicing gadgets and uses these teardown series to promote said gearâ"noted that the iPad mini looks on the outside like a smaller version of the new iPad Air. But on the inside, it's an updated iPad mini 4, the team wrote.

On opening the tablet up, iFixit discovered a 19.32Wh battery -- the same capacity as the previous-generation iPad mini. But there are some notable changes. The front-facing camera module has been updated to a 7-megapixel Æ'/2.2, like the 10.5-inch iPad Pro. That's a marked improvement over the iPad mini 4. There's also Apple's A12 Bionic system-on-a-chip (the same found in the iPhone XS, XS Max, and XR) with 3GB of LPDDR4X DRAM. The updated microphone array has been moved near the selfie cam, and new ambient light sensors support the True Tone feature, which adjusts the white balance of the display based on ambient light conditions for user comfort. The repair site gave the 2019 iPad mini a score of two out of 10 for repairability. "The only positive cited was that a single Phillips screwdriver can deal with all the screws in the device," Ars reports. "However, replacing the battery is 'unnecessarily difficult,' there's adhesive everywhere, and removing the home button (no small feat) is required in order to replace the screen."

After tearing apart Apple's new second-generation AirPods, the repair guide site found that there is no practical way to service or repair them even at a professional shop. They labeled them as "disappointingly disposable." Ars Technica reports: iFixit had to go to almost comical lengths to open the AirPods up, and despite their expertise and tools, the iFixit team was unable to do so without permanently damaging the product. [...] That's disappointing, given that the batteries in the AirPods won't last longer than a few years with heavy use, and they're hard to recycle. Apple does offer to recycle headphones through partners as part of its Apple GiveBack program, but the GiveBack Web portal does not offer a product-specific category for AirPods to consumers like it does with most other Apple products. Consumers may simply select a general "headphones & speakers" category on the site.

The teardown also revealed some differences from the first-generation AirPods. The battery is the same size, but iFixit identified the new, Bluetooth 5-ready H1 chip in the earbuds themselves. The site also found some small differences likely related to Apple's efforts to increase the case's water resistance. For all the details, visit iFixit's teardown page for the product. All told, iFixit gave the AirPods a 0 out of 10 for repairability -- that's low even for Apple products. By contrast, the site also opened up Samsung's Galaxy Buds and gave them a 6 out of 10.

After tearing apart Apple's new second-generation AirPods, the repair guide site found that there is no practical way to service or repair them even at a professional shop. They labeled them as "disappointingly disposable." Ars Technica reports: iFixit had to go to almost comical lengths to open the AirPods up, and despite their expertise and tools, the iFixit team was unable to do so without permanently damaging the product. [...] That's disappointing, given that the batteries in the AirPods won't last longer than a few years with heavy use, and they're hard to recycle. Apple does offer to recycle headphones through partners as part of its Apple GiveBack program, but the GiveBack Web portal does not offer a product-specific category for AirPods to consumers like it does with most other Apple products. Consumers may simply select a general "headphones & speakers" category on the site.

The teardown also revealed some differences from the first-generation AirPods. The battery is the same size, but iFixit identified the new, Bluetooth 5-ready H1 chip in the earbuds themselves. The site also found some small differences likely related to Apple's efforts to increase the case's water resistance. For all the details, visit iFixit's teardown page for the product. All told, iFixit gave the AirPods a 0 out of 10 for repairability -- that's low even for Apple products. By contrast, the site also opened up Samsung's Galaxy Buds and gave them a 6 out of 10.

iFixit has released their teardown of the new Mac mini, providing a look inside the portable desktop computer. Some of the notable findings include user-upgradable RAM and soldered CPU and SSD. Mac Rumors reports: While the RAM in the previous-gen Mac mini from 2014 was soldered to the logic board, the new Mac mini has user-upgradeable RAM, as discovered earlier this week. As seen in older iMacs, the RAM is protected by a perforated shield that allows the memory modules to operate at a high frequency of 2666 MHz without interfering with other device functions, according to iFixit. To upgrade the RAM, the shield can be removed by unfastening four Torx screws.

Other silicon on the logic board of this particular Mac mini includes the Apple T2 security chip, a 3.6GHz quad-core Intel Core i3 processor, Intel UHD Graphics 630, 128GB of flash storage from Toshiba, an Intel JHL7540 Thunderbolt 3 controller, and a Gigabit Ethernet controller from Broadcom. Despite the good news about the RAM, the CPU and SSD are soldered to the logic board, as are many ports, so this isn't a truly modular Mac mini. iFixit awarded the new Mac mini a repairability score of 6/10, with 10 being the easiest to repair, topping the latest MacBook Air, MacBook, MacBook Pro, iMac, and iMac Pro, and trailing only the 2013 Mac Pro.

iFixit tore apart Apple's iPhone XS and iPhone XS Max, revealing very similar insides to last year's iPhone X. Engadget reports the findings: One of the most interesting features is the battery on the XS. The iPhone XS sports a slightly downgraded battery from the iPhone X, a 10.13 Wh battery (2,659 mAh at 3.81 V) versus 10.35 Wh (2716 mAh at 3.81 V). But a new configuration might more than make up for it: Apple is using a brand-new L-shaped single-cell battery instead of two separate batteries. However, the XS Max still sports two batteries. Some other tweaks include a new, Apple-branded power management chip and a new antenna line on the bottom of the phone. The camera bump is also slightly taller, meaning your iPhone X case might not fit on your XS, if you plan on upgrading. The Verge also notes that "there's no evidence that the teardown team could find of any improved water or dust resistance, despite the improved IP68 ratings on the iPhone XS and XS Max."

An anonymous reader quotes a report from Motherboard: Someone has uploaded what appear to be 11 of Apple's internal repair videos to YouTube. Apple did not immediately respond to a request for comment, but two sources in the repair community familiar with Apple's repair policies told Motherboard these are indeed genuine Apple how-to videos. The videos themselves have an Apple copyright on them, the host references internal Apple documentation and diagnostic tests, and, most importantly, the videos use proprietary Apple disassembly and repair tools that Motherboard has previously confirmed are manufactured by and are exclusive to Apple.

The videos on how to open an iPhone X and replace its battery are particularly interesting, and show that the DIY repair community has gotten extremely good at reverse-engineering Apple's official procedures. The instructor walks the repair tech through the process of opening the case on the iPhone X in a way that closely mirrors the process that sites such as iFixit have been doing for a few years now. The video starts by instructing the tech to remove the screws near the lighting port, then inserting the iPhone X into a device that uses suction cups to pry the screen away from the body while the tech uses a small tool to cut the adhesive along the seams at the edge of the device. Apple's suction cup tool looks like a bulkier version of iFixit's iSclack tool -- a suction cup device that customers can use to disassemble and repair their own device. The video about replacing the iPhone X's battery is remarkably similar to the iFixit video of the same procedure.

Last week, Apple introduced a refreshed 9.7-inch iPad with Apple Pencil support. iFixit has published its teardown of the device this morning, and as The Verge points out, schools won't like how difficult it is to repair. From the report: The takeaway from all this is that the new iPad isn't going to be any easier to repair than prior generations, which were already borderline unrepairable. If an iPad breaks, there's almost no chance that a district will be able to repair it in-house; whereas on cheaper Chromebooks, there's a possibility an IT team could open them up to make some basic fixes. It's a weak point that it's hard to see Apple ever addressing. And since schools aren't exactly forgiving environments for a lent-out device, how well the iPad holds up to drops and dings, and how expensive it is to fix, are bound to be factors in a school's decision on which devices to adopt. Mac Rumors highlights the key findings from iFixit's teardown: The new iPad's lack of waterproofing, non-replaceable charging port, zero upgradeability, and use of glue throughout the internals added up to a "repair nightmare." iFixit then pointed towards the HP Elite x2 1012 G1 tablet, which got a perfect repairability score of 10 out of 10, summarizing that "Apple's 'education' iPad is still a case of won't -- not can't." One of the iPad's advantages in terms of repairability comes in the form of its digitizer panel easily separating from the display. iFixit pointed out that in the event that either component should break, repair will be easier for schools and educators. The sixth-gen iPad has the same battery as the previous model, with 32.9 Wh capacity. iFixit noted that while this allows Apple to reuse existing manufacturing lines to reduce waste, the battery is still locked behind a "repair-impeding adhesive" that greatly reduced the iPad's repairability score. Apple has provided easy battery removal before, in the 12.9-inch iPad Pro, but iFixit hasn't seen anything like it since. Ultimately, iFixit gave the 2018 iPad a repairability score of 2 out of 10, favoring the fairly easy repair options of its air-gapped, non-fused display and digitizer glass, but taking marks off for its heavy use of adhesive and sticky tape.

Popular repair site iFixit has acquired an iMac Pro and opened it up to see what's inside. They tore down the base iMac Pro with an 8-core processor, 32GB of RAM, and a 1TB SSD. Mac Rumors reports the findings: iFixit found that the RAM, CPU, and SSDs in the iMac Pro are modular and can potentially be replaced following purchase, but most of the key components "require a full disassembly to replace." Standard 27-inch iMacs have a small hatch in the back that allows easy access to the RAM for post-purchase upgrades, but that's missing in the iMac Pro. Apple has said that iMac Pro owners will need to get RAM replaced at an Apple Store or Apple Authorized Service Provider. iFixit says that compared to the 5K 27-inch iMac, replacing the RAM in the iMac Pro is indeed "a major undertaking."

Apple is using standard 288-pin DDR4 ECC RAM sticks with standard chips, which iFixit was able to upgrade using its own $2,000 RAM upgrade kit. A CPU upgrade is "theoretically possible," but because Apple uses a custom-made Intel chip, it's not clear if an upgrade is actually feasible. The same goes for the SSDs -- they're modular and removable, but custom made by Apple. Unlike the CPU, the GPU is BGA-soldered into place and cannot be removed. The internals of the iMac Pro are "totally different" from other iMacs, which is unsurprising as Apple said it introduced a new thermal design to accommodate the Xeon-W processors and Radeon Pro Vega GPUs built into the machines. The new thermal design includes an "enormous" dual-fan cooler, what iFixit says is a "ginormous heat sink," and a "big rear vent." Overall, iFixit gave the iMac Pro a repairability score of 3/10 since it's difficult to open and tough to get to internal components that might need to be repaired or replaced.

Popular repair site iFixit has acquired an iMac Pro and opened it up to see what's inside. They tore down the base iMac Pro with an 8-core processor, 32GB of RAM, and a 1TB SSD. Mac Rumors reports the findings: iFixit found that the RAM, CPU, and SSDs in the iMac Pro are modular and can potentially be replaced following purchase, but most of the key components "require a full disassembly to replace." Standard 27-inch iMacs have a small hatch in the back that allows easy access to the RAM for post-purchase upgrades, but that's missing in the iMac Pro. Apple has said that iMac Pro owners will need to get RAM replaced at an Apple Store or Apple Authorized Service Provider. iFixit says that compared to the 5K 27-inch iMac, replacing the RAM in the iMac Pro is indeed "a major undertaking."

Apple is using standard 288-pin DDR4 ECC RAM sticks with standard chips, which iFixit was able to upgrade using its own $2,000 RAM upgrade kit. A CPU upgrade is "theoretically possible," but because Apple uses a custom-made Intel chip, it's not clear if an upgrade is actually feasible. The same goes for the SSDs -- they're modular and removable, but custom made by Apple. Unlike the CPU, the GPU is BGA-soldered into place and cannot be removed. The internals of the iMac Pro are "totally different" from other iMacs, which is unsurprising as Apple said it introduced a new thermal design to accommodate the Xeon-W processors and Radeon Pro Vega GPUs built into the machines. The new thermal design includes an "enormous" dual-fan cooler, what iFixit says is a "ginormous heat sink," and a "big rear vent." Overall, iFixit gave the iMac Pro a repairability score of 3/10 since it's difficult to open and tough to get to internal components that might need to be repaired or replaced.

iFixit has posted its teardown of the iPhone X, revealing a new TrueDepth camera system, stacked logic board, L-shaped two-cell battery pack, and Qi-based inductive charging coil. Mac Rumors reports: Like every other model since the iPhone 7 Plus, the iPhone X is a sideways-opening device. A single bracket covers every logic board connector. iFixit said the miniaturized logic board design is incredibly space efficient, with an unprecedented density of connectors and components. It noted the iPhone X logic board is about 70 percent of the size of the iPhone 8 Plus logic board. The extra room allows for a new L-shaped two-cell battery pack rated for 2,716 mAh, which is slightly larger than the iPhone 8 Plus battery. iFixit's teardown includes some high-resolution photos of the iPhone X's new TrueDepth camera system that powers Face ID and Animoji. For those unfamiliar, a flood illuminator covers your face with infrared light. Next, the front-facing camera confirms a face. Then the IR dot projector projects a grid of dots over your face to create a three-dimensional map. Last, the infrared camera reads this map and sends the data to the iPhone X for authentication. Like the iPhone 8 and iPhone 8 Plus, the inside of the iPhone X's rear shell is affixed with an inductive charging coil based on the Qi standard. iFixit gave the iPhone X a so-called repairability score of six out of a possible 10 points. It said a cracked display can be replaced without removing Face ID's biometric hardware, but it added that fussy cables tie unrelated components together into complex assemblies that are expensive and troublesome to replace.

An anonymous reader quotes a report from Motherboard: Microsoft's latest Surface Laptop may have earned glowing reviews from certain sections of the tech press, but don't tell that to iFixit. The company, which provides repair tools and manuals for popular gadgets like the iPhone and PlayStation, has handed the Surface Laptop a score of 0 out of 10 in terms of user repairability, stating definitively that the laptop "is not meant to be opened or repaired; you can't get inside without inflicting a lot of damage." iFixit's detailed teardown illustrates just how difficult it is to open the Surface. For starters, there are no screws, proprietary or otherwise, on the outside of the laptop. Instead, the laptop is literally welded together using a type of "plastic soldering" that is rare to see in consumer electronics. Anyone hoping to get inside the "beautifully designed and crafted" computer will have to pry it open with a knife or dedicated pick in order to defeat Microsoft's plastic welding. Whether or not it's actually worth going through the trouble of defeating said welding is another matter, given that the "glue-filled monstrosity," as iFixit dubs the laptop, has none of the user-upgradeable parts you'd want to see in a PC, like memory or storage.

"It literally can't be opened without destroying it," the repair company concludes. "If we could give it a -1 out of 10, we would," iFixit said in an emailed statement on Friday. "It's a Russian nesting doll from hell with everything hidden under adhesive and plastic spot welds. It is physically impossible to nondestructively open this device."

According to an iFixit teardown, Apple's new 4K 21.5-inch iMac has both removable RAM and a Kaby Lake processor that's not soldered onto the logic board. Whereas the previous models had soldered memory modules, the new iMac's memory sit in two removable SO-DIMM slots. MacRumors reports: iFixit made the discovery by disassembling Apple's $1,299 mid-range 3.0GHz stock option, which includes 8GB of 2400MHz DDR4 memory, a Radeon Pro 555 graphics card with 2GB of VRAM, and a 1TB 5400-RPM hard drive. After slicing through the adhesive that secures the 4K display to the iMac's housing and removing the power supply, hard drive, and fan, iFixit discovered that the memory modules aren't soldered onto the logic board like previous models, but instead sit in two removable SO-DIMM slots. Similarly, after detaching the heatsink and removing the warranty voiding stickers on the backside of the logic board, iFixit found that the Intel SR32W Core i5-7400 Kaby Lake processor sits in a standard LGA 1151 CPU socket, making it possible to replace or upgrade the CPU without a reflow station.

Not long ago, Apple CEO Tim Cook explained why the company felt a need to remove the headphone jack from the new iPhones -- the iPhone 7 and iPhone 7 Plus. He said, "that jack takes up a lot of space in the phone, a lot of space. And there's a lot of more important things we can provide for the consumer than that jack." His colleague Phil Schiller cited "courage" for the same. As people learn to live in a world where they have to use a dongle to use their existing pair of headphones, gadget repair community iFixit found today that Apple isn't really using that "extra space" it got after getting rid of the headphone jack. BusinessInsider reports: "In place of the headphone jack, we find a component that seems to channel sound from outside the phone into the microphone... or from the Taptic Engine out," they write. Yep -- in the place where the headphone jack used to be there's a piece of molded plastic. "No fancy electronics here, just some well-designed acoustics and molded plastic," iFixit writes.iFixit adds, "Closer inspection shows a new, second lower speaker grille that leads ... nowhere? Interesting." Update: 09/16 21:21 GMT by M : Apple says it's a "barometric vent." The Verge reports: Apparently adding all the waterproofing to the iPhone 7 and 7 Plus meant that it was more of a sealed box, and so to be able to have an accurate and working barometer, Apple used that space. The barometer is the thing that allows a phone to measure altitude, and Apple points out that on the iPhone 7 it can measure even minor changes like climbing a flight of stairs.

An anonymous reader shares an article from Geek.com: The one thing that makes LG's G5, the flagship smartphone it launched in February, stand out from the crowd is its modularity. As iFixit learned, that means more than just being able to quickly swap the battery for a camera grip or DAC. In its teardown, iFixit found that LG has made it easy to replace lots of the G5's parts. The process might not be as simple as giving the phone a squeeze and sliding a module out, but it's a heck of a lot easier than it is with many phones and tablets. [...] All in all, it makes for a pretty tidy teardown and it earned the G5 an impressive 8/10.

An anonymous reader writes: The Apple Watch's release date has arrived: retailers around the world have quietly begun putting them on their shelves, and customers are beginning to receive their shipments. Reviews have been out for a while, including thoughtful ones from John Gruber and Nilay Patel. Apple has published a full user guide for the software, and iFixit has put up a full teardown to take a look at the hardware. They give it a repairability score of 5 out of 10, saying that the screen and battery are easily replaced, but not much else is. Though Apple designated the watch "water-resistant" rather than "waterproof", early tests show it's able to withstand a shower and a swim in the pool without failing. Ars has an article about the difficulty of making games for the Apple Watch, and Wired has a piece detailing its creation.

iFixit gives the new Retina iMac a score of 5 (out of 10) for repairability, and says that the new all-in-one is very little changed internally from the system (non-Retina) it succeeds. A few discoveries along the way: The new model "retains the familiar, easily accessible RAM upgrade slot from iMacs of yore"; the display panel (the one iin the machine disassmbled by iFixit at least) was manufactured by LG Display; except for that new display, "the hardware inside the iMac Intel 27" Retina 5K Display looks much the same as last year's 27" iMac." In typical iFixit style, the teardown is documented with high-resolution pictures and more technical details.

An anonymous reader writes with a teardown from iFixit of the Oculus Rift Development Kit 2: "iFixit's teardown reveals lots of interesting hardware within, including 40 infrared LEDs, a well-organized motherboard, and a display panel lifted directly from a Samsung Galaxy Note 3. They also took apart the IR tracking camera for good measure." The review is the usual iFixit blend of funny, concise and technical; they include a nice shot showing those IR sources embedded in the plastic of the frame. Why the straight-from-a-phone display? "This seems to make economical sense, since Oculus is working to ship something like 45,000 DK2s—a goodly number for a mid-development prototype, but certainly not enough to warrant a fully custom display."

snydeq writes "30 years ago today, Apple debuted the Macintosh. Here are some reviews of the early Mac models, including the Macintosh ('will be compared to other machines not only in terms of its features but also in the light of the lavish claims and promises made by Apple co-founder Steven Jobs'), the Mac SE ('contains some radical changes, including room for a second internal drive and even a fan'), the Mac IIx ('a chorus of yawns'), and the Mac Portable ('you may develop a bad case of the wannas for this lovable [16-lb.] luggable'). Plus insights on the Macintosh II's prospects from Bill Gates: 'If you look at a product like Mac Word III on that full-page display, it's pretty awesome. ... But the corporate buyer is never going to be a strong point for Apple.'" iFixit got their hands on a Mac 128K and did a teardown, evaluating the old hardware for repairability. What will the Mac look like in another 30 years?

iFixit has posted a teardown of Apple's new soda-can-shaped Mac Pro. Despite the unusual form factor, it earned a relatively high repairability score: 8/10. iFixit said, "For being so compact, the design is surprisingly modular and easy to disassemble. Non-proprietary Torx screws are used throughout, and several components can be replaced independently." They say it's easy to access the fan and the RAM slots, and while the CPU is buried a bit more deeply, it's still user-replaceable. The Mac Pro doesn't get higher than an 8 because its uses some proprietary connectors and the cable routing is cramped. They add, "There is no room, or available port, for adding your own internal storage. Apple has addressed this with heaps of Thunderbolt, but we'd personally rather use the more widely compatible SATA if we could."

Microsoft released the Xbox One today, putting the next-gen console war into full swing. A common theme throughout most of the reviews is that properly evaluating the system is going to take time. Not only are updates for the console continuing to roll out, but the usefulness of some of its technology will depend on what game-makers and other content producers can do with it. Digital Foundry says, "It is willing to make the trades on gaming power in order to potentially revolutionize the way we interact with entertainment in the living room." The Penny Arcade Report calls the hardware and UI a "confusing mess" — until you learn to use it, at which point the hands-free navigation is fast and convenient. Polygon's review is once again visually-oriented, providing a good look at the UI, comparing the controller with the Xbox 360's controller, and giving a demonstration of how Kinect recognizes users. Their conclusion is that while "Kinect isn't a fully realized product yet," "the Xbox One feels like it's from the future." iFixit has a full teardown of the Xbox One, giving it a repairability score of 8/10 (the Kinect sensor gets 6/10). HotHardware has more details about the console's internals, including power consumption and temperature readings. Eurogamer has a compilation of launch coverage, including launch title reviews.

Microsoft released the Xbox One today, putting the next-gen console war into full swing. A common theme throughout most of the reviews is that properly evaluating the system is going to take time. Not only are updates for the console continuing to roll out, but the usefulness of some of its technology will depend on what game-makers and other content producers can do with it. Digital Foundry says, "It is willing to make the trades on gaming power in order to potentially revolutionize the way we interact with entertainment in the living room." The Penny Arcade Report calls the hardware and UI a "confusing mess" — until you learn to use it, at which point the hands-free navigation is fast and convenient. Polygon's review is once again visually-oriented, providing a good look at the UI, comparing the controller with the Xbox 360's controller, and giving a demonstration of how Kinect recognizes users. Their conclusion is that while "Kinect isn't a fully realized product yet," "the Xbox One feels like it's from the future." iFixit has a full teardown of the Xbox One, giving it a repairability score of 8/10 (the Kinect sensor gets 6/10). HotHardware has more details about the console's internals, including power consumption and temperature readings. Eurogamer has a compilation of launch coverage, including launch title reviews.

Today marks the launch of the latest entrant to the next-gen console race: Sony's PlayStation 4. A number of reviews for the system have already gone up, but many outlets are waiting for next Friday's Xbox One launch before passing final judgment. With regard to the PS4's hardware and UI, Digital Foundry praises the DualShock 4 controller design and the improvements to background downloading, while worrying about fan noise in warmer environments. iFixit provides a step-by-step teardown of the device, giving it an 8/10 repairability score. Ars has many good things to say, but many bad things as well: "The PlayStation 4 has an excellent controller, decently powerful hardware, some intriguing, well-executed new features, and an interface that shows belated acknowledgment of some of Sony's most user-unfriendly past designs. It also has a lot of features that are half-assed, missing, or downright bewildering at this point." Polygon's review is more visually oriented, filled with pictures, videos, and drawings. They conclude, "[T]he PlayStation 4's focus on gaming — and only gaming — is undermined by a distinct lack of compelling software. That failing is sure to improve — better games and more of them will appear on the PlayStation 4 — but right now, this is a game console without a game to recommend it." Eurogamer's coverage includes has a round-up of launch title reviews and gameplay videos. IGN has coverage of the roughly 0.4% of PS4s that arrive broken out of the box, and Kotaku explains how they fixed theirs.

MojoKid writes "News of a proven security vulnerability involving Apple iOS 7 has started making the rounds. The exploit specifically involves the lockscreen, the most common piece of security that stops an unauthorized individual from gaining access to anything important on your phone. The 'hack,' if you want to call it that, is simple: Swipe up on the lock screen to enter the control center, and then open the alarm clock. From there, hold the phone's sleep button to bring up a prompt that will ask you if you wish to shut down, but instead of doing that, hit the cancel option, and then tap the home button to access the phone's multi-tasking screen. With access to this multi-tasking screen, anyone could try opening up what you've already had open on your phone. If you had Twitter open, for example, this person might be able to pick up where you left off and post on your behalf. Or, they could access the camera — and of course, every single photo stored on the phone." The new iPhone models were released today; iFixit has a teardown of the iPhone 5s, giving it a repairability score of 6/10.

iFixit's been breaking devices and voiding warranties for years now; latest on their chopping block is the new Moto X from Motorola, a phone hawked as much for its customizability and place of manufacture (the U.S.) as for anything else. You might expect a highly hyped, ultra-customizable phone to be made of high-end components and ultra-repairable as well. iFixit's teardown commentary has both some good and only-middlin' things to say about the innards, but very little bad. They call out the highly modular headphone jack, and say "a considerable amount of effort went in to the internal design of this device; the number of clips and contacts we've found so far is a great testament to that."

adeelarshad82 writes "While it's more limited than the Roku 3 and by no means Google's answer to Airplay, Chromecast sets itself apart from other similar products simply based on its price and potential of bringing Internet HDTV streaming to many more people than before. Priced at only $35, it's a direct stick that plugs into your HDTV's HDMI port and lets you stream media from Netflix, YouTube, and Google Play through your smartphone, tablet, or notebook. Unlike the Roku Stick, it uses a separate micro-USB port instead of MHL to power it. This on one hand means you need to run a cable from the stick to a USB port, making it much less neat than it would seem. On the other hand, it means the stick works with any HDTV, whether it has an MHL-capable HDMI port or not. Once connected, the setup itself is fairly simple and entirely app-controlled. Past the setup, your streaming content choices are currently limited, though Google released an API for the Chromecast, so more apps could support it in the future. For now Android users can stream media from Google Play Movies and Music, as well as Netflix and YouTube whereas iOS users can watch Netflix and YouTube via the Chromecast. From a computer, users can stream media from Netflix, YouTube, Google Play, and Chrome. Unlike Apple TV and AirPlay, Chromecast doesn't let you stream your locally stored media. In fact Google Play Music gives an error message when you try to play music you loaded on your device yourself and not through the Google Play store. All in all, at $35 it's the most affordable way to access online media services on your HDTV." El Reg also got their hands on one. Alas, one perk of grabbing the Chromecast is gone: Google ended the free three month Netflix bundle that was worth almost as much as the cost of the Chromecast itself after sales were much higher than expected (so high it looks like they ran out of them after only a day). Update: 07/26 21:20 GMT by U L : iFixIt posted a teardown of the Chromecast.

netbuzz writes "In a clever bit of self-promotion, the do-it-yourself repair evangelists at iFixit announced today that they will be giving away 1,776 free 'iPhone liberation kits' that will allow Apple customers access to the inner workings of their devices by replacing the difficult-to-remove pentalobe screws with standard Phillips screws. 'Get a free insurance policy,' iFixit says. 'In the unfortunate event that your iPhone needs repair, you will be set to make any necessary fix. For situations when you need to get the battery out of your iPhone as quickly as possible—such as after dropping the device into water—you will be ready.'"

iFixit has posted a detailed teardown of the new iPhone 5. While the casing still uses Apple's proprietary pentalobe fasteners, the good news is that Apple has made the screen much easier to remove. Once the fasteners have been removed, the screen will lift out easily through the use of a suction cup. The screens are by far the most common parts of iPhones to break, and this change turns a complicated 38-step procedure that takes about 45 minutes at minimum into a quick, 5-10 minute job. The teardown also shows the iPhone 5 battery to be very similar to the iPhone 4S's, suggesting that the improvements to battery life come from other hardware and software changes. We get a look at the new A6 processor running the phone, which is a custom design based on ARMv7. iFixit also looks at the Lightning connector assembly; unfortunately, it includes the loudspeaker, bottom microphone, Wi-Fi antenna, and headphone jack as well, so fixing any one of those parts individually will be difficult. Whatever you think of Apple's decision to move to Lightning instead of micro-USB, it seems their switch away from the 30-pin connecter was necessitated by size constraints.

iFixit has posted a detailed teardown of the new iPhone 5. While the casing still uses Apple's proprietary pentalobe fasteners, the good news is that Apple has made the screen much easier to remove. Once the fasteners have been removed, the screen will lift out easily through the use of a suction cup. The screens are by far the most common parts of iPhones to break, and this change turns a complicated 38-step procedure that takes about 45 minutes at minimum into a quick, 5-10 minute job. The teardown also shows the iPhone 5 battery to be very similar to the iPhone 4S's, suggesting that the improvements to battery life come from other hardware and software changes. We get a look at the new A6 processor running the phone, which is a custom design based on ARMv7. iFixit also looks at the Lightning connector assembly; unfortunately, it includes the loudspeaker, bottom microphone, Wi-Fi antenna, and headphone jack as well, so fixing any one of those parts individually will be difficult. Whatever you think of Apple's decision to move to Lightning instead of micro-USB, it seems their switch away from the 30-pin connecter was necessitated by size constraints.

sl4shd0rk writes "Among the much ballyhooed tech at Google I/O last week was the Google Nexus Q. Google made an effort to proudly point out the device was "Made in the USA" and even had it stamped on the back of it. A tear-down at ifixit.com however, reveals the guts of the thing are mostly manufactured overseas at the expected locations (China, Taiwan, Japan, Korea, et al). Wired also posted a tear-down in which they reveal a die-casting shop in Wisconsin is the source of the zinc housing, but certainly not the entire device as some news sources reported. It's great that Google decided to utilize the struggling U.S. manufacturing sector for this, but claiming the device is USA made, and being blatantly vague about its origins is quite misleading." How struggling the U.S. manufacturing sector is depends on who you ask and how you measure, remember.

sl4shd0rk writes "Among the much ballyhooed tech at Google I/O last week was the Google Nexus Q. Google made an effort to proudly point out the device was "Made in the USA" and even had it stamped on the back of it. A tear-down at ifixit.com however, reveals the guts of the thing are mostly manufactured overseas at the expected locations (China, Taiwan, Japan, Korea, et al). Wired also posted a tear-down in which they reveal a die-casting shop in Wisconsin is the source of the zinc housing, but certainly not the entire device as some news sources reported. It's great that Google decided to utilize the struggling U.S. manufacturing sector for this, but claiming the device is USA made, and being blatantly vague about its origins is quite misleading." How struggling the U.S. manufacturing sector is depends on who you ask and how you measure, remember.

zacharye writes with news that Motorola has reinvented their popular RAZR clam-shell phone as an Android smartphone. The new device is 4G LTE-capable and 7.1mm thick, and it contains "a 1.2GHz dual-core TI OMAP processor, a 4.3-inch qHD Super AMOLED display, 1GB of RAM, an 8-megapixel camera with 1080p HD video capture, an LED flash, an HDMI-out port, noise cancellation capabilities, 16GB of built-in storage and a 16GB microSD card pre-installed." iFixit did a teardown of the phone, finding that the construction necessary for such thinness will make repairs problematic.

fysdt writes "The FBI's use of GPS vehicle tracking devices is becoming a contentious privacy issue in the courts, with the Obama administration seeking Supreme Court approval for its use of the devices without a warrant, and a federal civil rights lawsuit targeting the Justice Department for tracking the movements of an Arab-American student. In the midst of this legal controversy, Threat Level decided to take a look at the inside of one of the devices, with the help of the teardown artists at iFixit."

RedEaredSlider writes "Shorty after the US launch of Nintendo's last portable console, 3DS owners have begun reporting issues with the device. In one case, dubbed the 'black screen of death,' users reported instances where their 3DS screens grew black shortly before their consoles became unresponsive. Other owners documented errors involving a screen instructing them to restart their systems. Nintendo has taken notice of the issues, and offered 3DS users a fix for the error. 'If anyone is experiencing any problems with their Nintendo 3DS console, we recommend that in the first instance they download and install the latest system update, now available online,' the company said in a statement." The 3DS's launch was reportedly more successful than the DSi's. iFixit did a nice teardown of the device a while back, and Nukezilla's Peter Silk put the screen under a microscope.

CWmike writes "Apple's new MacBook Pro shows some build-quality problems that shouldn't be seen in a notebook that costs $1,800, a teardown expert said on Monday. iFixit.com found several signs of substandard assembly while disassembling a 15-in. MacBook Pro. Among them: A stripped screw near the subwoofer enclosure and an unlocked ZIF (zero insertion force) socket for the IR (infrared) sensor. '[These] should not be things found inside a completely unmolested computer with an $1,800 base price,' iFixit said in the teardown description. iFixit also spotted an unusual amount of thermal paste applied to both the CPU and the GPU. 'Holy thermal paste! Time will tell if the gobs of thermal paste applied to the CPU and GPU will cause overheating issues down the road,' iFixit said. The refreshed MacBook Pro models launched last Thursday in what one analyst called a 'ho-hum' upgrade."

Pickens writes "Network World reports that in the past if you wanted to remove the outer case on your iPhone 4 to replace the battery or a broken screen, you could use a Phillips screwdriver to remove two tiny screws at the base of the phone and then simply slide off the back cover. But now Apple is replacing the outer screw with a mysterious tamper-resistant 'pentalobular' screw across its most popular product lines, making it harder for do-it-yourselfers to make repairs. What about existing products in the field? Pentalobular screws might find their way into them, too. 'Apple's latest policy will make your blood boil,' says Kyle Wiens, CEO of iFixit. 'If you take your iPhone 4 into Apple for any kind of service, they will sabotage it by replacing your Phillips screws with the new, tamper-resistant screws. We've spoken with the Apple Store geniuses tasked with carrying out this policy, and they are ashamed of the practice.' Of course, only Apple-authorized service technicians have Pentalobular screwdrivers and they're not allowed to resell them. 'Apple sees a huge profit potential,' says Wiens. 'A hundred dollars per year in incremental revenue on their installed base is a tremendous opportunity.'"

alphadogg writes "Microsoft's new hands-free Kinect game controller is packed with four microphones, two autofocus cameras and a motion detector chip that together make for one heck of a complex toy, according to iFixit's initial teardown of the device. 'We haven't been this excited to get our hands on new hardware since the iPad,' says Kyle Wiens, CEO of the company. 'The way that we interact with computers is (finally) evolving, and Kinect is unlike any hardware we've ever taken apart. In fact, the only thing we've ever taken apart that has anywhere close to this many sensors is Pleo, the dinosaur robot.' iFixit describes Kinect as 'a horizontal bar of sensors connected to a small, motorized pivoting base.' The $150 device that Microsoft put hundreds of millions of dollars of research into can be purchased separately from the Xbox 360 or as part of a bundle. A Prime Sense PS1080-A2 is at the heart of Kinect's motion detection capabilities, as it connects to all of Kinect's sensors and processes images of your game room's color and scope before shooting them over to the Xbox. iFixit couldn't immediately identify all of the chips within the box, so plans to update its teardown."

itwbennett writes "The PlayStation Move hit retail stores on Friday and blogger Peter Smith spent the weekend putting it (and his shoulder) through its paces. So how does this motion controller compare to the Wii? Smith says it 'felt a lot more precise' but that 'there were instances where the depth perception of the camera got lost for a moment.' The bottom line: 'If you have a Wii and the Wii Motion Plus accessory, there isn't a whole lot here right now to justify $100-$170 worth of gear for most gamers.'" CNET is similarly critical, complaining of the continual calibration requirements and the dearth of good launch titles. The Guardian's games blog agrees that quality games are currently lacking, but says the accuracy and responsiveness are a step up from the Wii, giving the Move a lot of potential. iFixit did a teardown, providing an interesting look at the hardware inside the device.

sk8pmp writes with news that iFixit, a website known for Apple gadget teardowns and repair guides, is expanding into the game console market, launching a series of troubleshooting and repair guides to help gamers fix their own machines. They're also starting to sell replacement parts and the tools necessary to work on them. "Right now there are repair guides for 24 gaming consoles, including 206 repairs and upgrades. Some of these fixes deal with major issues, such as the infamous Red Ring of Death from the Xbox 360, but others are simpler. For instance, right now there is no easy way to clean out the fans inside your console. 'I think this is probably the number one cause of overheating these days now that manufacturers have mostly gotten their act together,' Wiens said. 'This is routine maintenance, and it's mind-boggling that the manufacturers don't provide people with an easy way to open the case up and blow it out.' You'll also learn how to replace broken LCD screens on your portables, replace the motherboard on your PlayStation 3, and do just about anything else you might want to do to these systems, from the simple to the harrowing."

Apple's much-awaited iPad officially launched today, and iFixit has gotten their hands on photos from the FCC teardown. They've done an analysis of the internals and provided directions on doing it yourself, if you're so inclined. Predictably, it's a hot topic in the media. Cory Doctorow wrote about why he won't be getting an iPad, complaining about the closed, hacker-unfriendly design and what he calls the "Wal-martization of the software channel." Daring Fireball's John Gruber disagrees, pointing out that enthusiasts — even kids exercising their curiosity — are still quite capable of playing around with the iPad through app creation, and with much more of a chance to compete with big companies than in the Apple ][ days. Similarly, others are referring to it as the "bedtime computer" — technology that has a reasonable shot at expanding into completely new areas of use, like bedtime reading for kids. Such a device was predicted in 1972 by Alan Kay, the PARC scientist credited with the epigram "The best way to predict the future is to invent it." His hypothetical DynaBook bears striking similarity to what Apple finally came up with. So, those of you who have picked up or received an iPad already: how do you like it?

Apple's much-awaited iPad officially launched today, and iFixit has gotten their hands on photos from the FCC teardown. They've done an analysis of the internals and provided directions on doing it yourself, if you're so inclined. Predictably, it's a hot topic in the media. Cory Doctorow wrote about why he won't be getting an iPad, complaining about the closed, hacker-unfriendly design and what he calls the "Wal-martization of the software channel." Daring Fireball's John Gruber disagrees, pointing out that enthusiasts — even kids exercising their curiosity — are still quite capable of playing around with the iPad through app creation, and with much more of a chance to compete with big companies than in the Apple ][ days. Similarly, others are referring to it as the "bedtime computer" — technology that has a reasonable shot at expanding into completely new areas of use, like bedtime reading for kids. Such a device was predicted in 1972 by Alan Kay, the PARC scientist credited with the epigram "The best way to predict the future is to invent it." His hypothetical DynaBook bears striking similarity to what Apple finally came up with. So, those of you who have picked up or received an iPad already: how do you like it?

An anonymous reader writes "Yesterday iFixit tore apart the Nintendo DSi and found several internal upgrades from the outgoing DS Lite. It seems that an experienced hand can completely disassemble the DSi in less than ten minutes using standard tools, especially since the job does not require a tri-wing screwdriver. This should make repairing and tinkering with the DSi substantially easier. The DSi now includes two integrated cameras that, unfortunately, have only 0.3 megapixel resolution. This is certainly a bit underwhelming considering most mainstream phones have cameras of at least 1.3 megapixels. As for chips, Nintendo is using a Samsung MoviNAND integrated 256 MB Flash memory / MMC controller chip, as well as a custom ARM CPU + GPU is stamped with the revision code 'TWL.' The DSi's chips all had manufacture dates around September 2008, indicating that Nintendo has been stockpiling these devices for quite a while prior to the North American release."

kwiens writes "We just took apart a MacBook and posted some disassembly instructions and hi-res logic board photos. It looks like Apple's saving a bunch of R&D by using stock Intel chips in the MacBook Pro. Interestingly, the built-in iSight and Bluetooth connectors are USB 2.0. Apple also downgraded some features from the Powerbook: half the DVD-R write speed and no Firewire 800."

kwiens writes "We just took apart a MacBook and posted some disassembly instructions and hi-res logic board photos. It looks like Apple's saving a bunch of R&D by using stock Intel chips in the MacBook Pro. Interestingly, the built-in iSight and Bluetooth connectors are USB 2.0. Apple also downgraded some features from the Powerbook: half the DVD-R write speed and no Firewire 800."

kwiens writes "We just took apart a MacBook and posted some disassembly instructions and hi-res logic board photos. It looks like Apple's saving a bunch of R&D by using stock Intel chips in the MacBook Pro. Interestingly, the built-in iSight and Bluetooth connectors are USB 2.0. Apple also downgraded some features from the Powerbook: half the DVD-R write speed and no Firewire 800."